HS Codes - 39: PLASTICS AND ARTICLES THEREOF
| 3901 | Polymers of ethylene, in primary forms |
| 3901.A | Polyethylene having a specific gravity of less than 0.94 |
| 3901.A.A | Linear polyethylene |
| - | High flow linear low density polyethylene-1-butene / lldpe (cas rn 25087-34-7) in form of powder, with -a melt flow rate (mfr 190 °c/2.16 kg) of 16g/10min or more, but not more than 24 g/10 min and -a density (astm d 1505) of 0.922 g/cm³ or more, but not more than 0.926 g/cm³ and -a vicat softening temperature of min. 94 °c |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.924 g/cm³ or more but not more than 0.928 g/cm³,-a melt flow rate (190 °c/2.16 kg) of 48 g/10 min or more but not more than 52 g/10 min, and-a peak melting temperature of 120 °c or more but not more than 124 °c |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.922 g/cm³ or more but not more than 0.926 g/cm³ and-a melt flow rate (190 °c/2.16 kg) of 18 g/10 min or more but not more than 22 g/10 min |
| - | Other |
| 3901.A.B | Other |
| - | Polyethylene granules, containing by weight 10% or more but not more than 25% of copper |
| - | Other |
| 3901.B | Polyethylene having a specific gravity of 0.94 or more |
| - | Polyethylene in one of the forms mentioned in note 6(b) to this chapter, of a specific gravity of 0.958 or more at 23 °c, containing: - 50 mg/kg or less of aluminium, - 2 mg/kg or less of calcium, - 2 mg/kg or less of chromium, - 2 mg/kg or less of iron, - 2 mg/kg or less of nickel, - 2 mg/kg or less of titanium and - 8 mg/kg or less of vanadium, for the manufacture of chlorosulphonated polyethylene |
| - | Other |
| 3901.C | Ethylene-vinyl acetate copolymers |
| - | For cavity filling, for use in certain types of aircraft |
| - | Copolymer of ethylene and vinyl acetate (cas rn 24937-78-8) -containing by weight 28% or more but not more than 49% of vinyl acetate, -with a melt flow rate of less than 5g/10 min (190 °c/2.16 kg, astm d1238),-in the form of pellets |
| - | Terpolymer of ethylene, vinyl acetate and methacrylic acid (cas rn 26375-31-5) |
| - | Other |
| 3901.D | Ethylene-alpha-olefin copolymers, having a specific gravity of less than 0.94 |
| - | High flow linear low density polyethylene-1-butene / lldpe (cas rn 25087-34-7) in form of powder, with -a melt flow rate (mfr 190 °c/2.16 kg) of 16g/10 min or more, but not more than 24 g/10 min and -a density (astm d 1505) of 0.922 g/cm³ or more, but not more than 0.926 g/cm³ and -a vicat softening temperature of min. 94 °c |
| - | Octene linear low-density polyethylene (lldpe) produced by a ziegler-natta catalyst method in the form of pellets with:- more than 10% but not more than 20% by weight of copolymer,- a melt flow rate (mfr 190°c/2.16 kg) of 0.7 g / 10 min or more but not more than 0.9 g / 10 min, and- a density (astm d4703) of 0.911 g/cm³ or more, but not more than 0.913 g/cm³for use in the co-extrusion processing of films for flexible food packaging |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.924 g/cm³ or more but not more than 0.928 g/cm³,-a melt flow rate (190 °c/2.16 kg) of 48 g/10 min or more but not more than 52 g/10 min, and-a peak melting temperature of 120 °c or more but not more than 124 °c |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.922 g/cm³ or more but not more than 0.926 g/cm³ and-a melt flow rate (190 °c/2.16 kg) of 18 g/10 min or more but not more than 22 g/10 min |
| - | Other |
| 3901.E | Other |
| - | Ionomer resin consisting of a salt of a terpolymer of ethylene with isobutyl acrylate and methacrylic acid; a-b-a block copolymer of polystyrene, ethylene-butylene copolymer and polystyrene, containing by weight 35% or less of styrene, in one of the forms mentioned in note 6(b) to this chapter |
| 3901.E.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| 3901.E.A.A | Other |
| - | Copolymer of ethylene and acrylic acid (cas rn 9010-77-9) with- an acrylic acid content of 18.5% or more but not more than 49.5% by weight (astm d4094), and- a melt flow rate of 10g/10 min (mfr 125 °c/2.16 kg, astm d1238) or more |
| - | Zinc or sodium salt of an ethylene and acrylic acid copolymer, with:- an acrylic acid content of 6% or more but not more than 50% by weight, and- a melt flow rate of 1g/10 min or more at 190 °c/2.16 kg (measured using astm d1238) |
| - | Copolymer made exclusively from ethylene and methacrylic acid monomers in which the methacrylic acid content is 11% by weight or more |
| - | Mixture containing by weight- 80% or more, but not more than 94% of chlorinated polyethylene (cas rn 64754-90-1) and- 6% or more, but not more than 20% of styrene-acrylic copolymer (cas rn 27136-15-8) |
| - | Terpolymer of ethylene, isobutyl acrylate and methacrylic acid (cas rn 37433-35-5), in the form of pellets |
| - | Terpolymer of ethylene, n-butyl acrylate and carbon monoxide (cas rn 61843-70-7) in the form of pellets |
| - | Ionomer resin consisting of a salt of a copolymer of ethylene with methacrylic acid |
| - | Chlorosulphonated polyethylene |
| - | Copolymer of ethylene, vinyl acetate and carbon monoxide, for use as a plasticizer in the manufacture of roof sheets |
| - | Mixtures of a-b block copolymer of polystyrene and ethylene-butylene copolymer and a-b-a block copolymer of polystyrene, ethylene-butylene copolymer and polystyrene, containing by weight not more than 35% of styrene |
| - | Chlorinated polyethylene, in the form of powder |
| - | Other |
| 3901 | Polymers of ethylene, in primary forms |
| 3901.F | Polyethylene having a specific gravity of less than 0.94 |
| 3901.F.A | Linear polyethylene |
| - | High flow linear low density polyethylene-1-butene / lldpe (cas rn 25087-34-7) in form of powder, with -a melt flow rate (mfr 190 °c/2.16 kg) of 16g/10min or more, but not more than 24 g/10 min and -a density (astm d 1505) of 0.922 g/cm³ or more, but not more than 0.926 g/cm³ and -a vicat softening temperature of min. 94 °c |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.924 g/cm³ or more but not more than 0.928 g/cm³,-a melt flow rate (190 °c/2.16 kg) of 48 g/10 min or more but not more than 52 g/10 min, and-a peak melting temperature of 120 °c or more but not more than 124 °c |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.922 g/cm³ or more but not more than 0.926 g/cm³ and-a melt flow rate (190 °c/2.16 kg) of 18 g/10 min or more but not more than 22 g/10 min |
| - | Other |
| 3901.F.B | Other |
| - | Polyethylene granules, containing by weight 10% or more but not more than 25% of copper |
| - | Other |
| 3901.G | Polyethylene having a specific gravity of 0.94 or more |
| - | Polyethylene in one of the forms mentioned in note 6(b) to this chapter, of a specific gravity of 0.958 or more at 23 °c, containing: - 50 mg/kg or less of aluminium, - 2 mg/kg or less of calcium, - 2 mg/kg or less of chromium, - 2 mg/kg or less of iron, - 2 mg/kg or less of nickel, - 2 mg/kg or less of titanium and - 8 mg/kg or less of vanadium, for the manufacture of chlorosulphonated polyethylene |
| - | Other |
| 3901.H | Ethylene-vinyl acetate copolymers |
| - | For cavity filling, for use in certain types of aircraft |
| - | Copolymer of ethylene and vinyl acetate (cas rn 24937-78-8) -containing by weight 28% or more but not more than 49% of vinyl acetate, -with a melt flow rate of less than 5g/10 min (190 °c/2.16 kg, astm d1238),-in the form of pellets |
| - | Terpolymer of ethylene, vinyl acetate and methacrylic acid (cas rn 26375-31-5) |
| - | Other |
| 3901.I | Ethylene-alpha-olefin copolymers, having a specific gravity of less than 0.94 |
| - | High flow linear low density polyethylene-1-butene / lldpe (cas rn 25087-34-7) in form of powder, with -a melt flow rate (mfr 190 °c/2.16 kg) of 16g/10 min or more, but not more than 24 g/10 min and -a density (astm d 1505) of 0.922 g/cm³ or more, but not more than 0.926 g/cm³ and -a vicat softening temperature of min. 94 °c |
| - | Octene linear low-density polyethylene (lldpe) produced by a ziegler-natta catalyst method in the form of pellets with:- more than 10% but not more than 20% by weight of copolymer,- a melt flow rate (mfr 190°c/2.16 kg) of 0.7 g / 10 min or more but not more than 0.9 g / 10 min, and- a density (astm d4703) of 0.911 g/cm³ or more, but not more than 0.913 g/cm³for use in the co-extrusion processing of films for flexible food packaging |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.924 g/cm³ or more but not more than 0.928 g/cm³,-a melt flow rate (190 °c/2.16 kg) of 48 g/10 min or more but not more than 52 g/10 min, and-a peak melting temperature of 120 °c or more but not more than 124 °c |
| - | Copolymer of ethylene and 1-butene (cas rn 25087-34-7) with: -a density (astm d 1505) of 0.922 g/cm³ or more but not more than 0.926 g/cm³ and-a melt flow rate (190 °c/2.16 kg) of 18 g/10 min or more but not more than 22 g/10 min |
| - | Other |
| 3901.J | Other |
| - | Ionomer resin consisting of a salt of a terpolymer of ethylene with isobutyl acrylate and methacrylic acid; a-b-a block copolymer of polystyrene, ethylene-butylene copolymer and polystyrene, containing by weight 35% or less of styrene, in one of the forms mentioned in note 6(b) to this chapter |
| 3901.J.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| 3901.J.A.A | Other |
| - | Copolymer of ethylene and acrylic acid (cas rn 9010-77-9) with- an acrylic acid content of 18.5% or more but not more than 49.5% by weight (astm d4094), and- a melt flow rate of 10g/10 min (mfr 125 °c/2.16 kg, astm d1238) or more |
| - | Zinc or sodium salt of an ethylene and acrylic acid copolymer, with:- an acrylic acid content of 6% or more but not more than 50% by weight, and- a melt flow rate of 1g/10 min or more at 190 °c/2.16 kg (measured using astm d1238) |
| - | Copolymer made exclusively from ethylene and methacrylic acid monomers in which the methacrylic acid content is 11% by weight or more |
| - | Mixture containing by weight- 80% or more, but not more than 94% of chlorinated polyethylene (cas rn 64754-90-1) and- 6% or more, but not more than 20% of styrene-acrylic copolymer (cas rn 27136-15-8) |
| - | Terpolymer of ethylene, isobutyl acrylate and methacrylic acid (cas rn 37433-35-5), in the form of pellets |
| - | Terpolymer of ethylene, n-butyl acrylate and carbon monoxide (cas rn 61843-70-7) in the form of pellets |
| - | Ionomer resin consisting of a salt of a copolymer of ethylene with methacrylic acid |
| - | Chlorosulphonated polyethylene |
| - | Copolymer of ethylene, vinyl acetate and carbon monoxide, for use as a plasticizer in the manufacture of roof sheets |
| - | Mixtures of a-b block copolymer of polystyrene and ethylene-butylene copolymer and a-b-a block copolymer of polystyrene, ethylene-butylene copolymer and polystyrene, containing by weight not more than 35% of styrene |
| - | Chlorinated polyethylene, in the form of powder |
| - | Other |
| 3902 | Polymers of propylene or of other olefins, in primary forms |
| 3902.A | Polypropylene |
| - | Polypropylene, containing no plasticiser,- of a melting point of more than 150 °c (as determined by the astm d 3417 method),- of a heat of fusion of 15 j/g or more but not more than 70 j/g,- of an elongation at break of 1 000% or more (as determined by the astm d 638 method),- of a tensile modulus of 69 mpa or more but not more than 379 mpa (as determined by the astm d 638 method) |
| - | Other |
| 3902.B | Polyisobutylene |
| - | Hydrogenated polyisobutene, in liquid form |
| - | Other |
| 3902.C | Propylene copolymers |
| - | For cavity filling, for use in certain types of aircraft |
| 3902.C.A | Other |
| - | Hydrogenated block copolymer of styrene and isoprene (cas rn 68648-89-5), containing by weight less than 37% of styrene |
| - | Hydrogenated copolymer of styrene, isoprene and butadiene, containing by weight 28% or more, but not more than 55% of propylene |
| - | A-b-a block copolymer, consisting of:- a copolymer of propylene and ethylene and- 21% (± 3%) by weight of polystyrene |
| - | Liquid ethylene-propylene-copolymer with:- a flashpoint of 250 °c or more,- a viscosity index of 150 or more,- of a number average molecular weight (m@n) of 650 or more |
| - | Other |
| 3902.D | Other |
| - | A-b-a block copolymer of polystyrene, ethylene-butylene copolymer and polystyrene, containing by weight 35% or less of styrene, in one of the forms mentioned in note 6(b) to this chapter |
| - | Polybut-1-ene, a copolymer of but-1-ene with ethylene containing by weight 10% or less of ethylene, or a blend of polybut-1-ene with polyethylene and/or polypropylene containing by weight 10% or less of polyethylene and/or 25% or less of polypropylene, in one of the forms mentioned in note 6(b) to this chapter |
| 3902.D.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| 3902.D.A.A | Other |
| - | Non-hydrogenated 100% aliphatic resin (polymer), with the following characteristics:- liquid at room temperature- obtained by cationic polymerisation of c-5 alkenes monomers- with a number average molecular weight (mn) of 370 (± 50)- with a weight average molecular weight (mw) of 500 (± 100) |
| - | Brominated butadiene-styrene copolymer (cas rn 1195978-93-8) with a bromine content of 60% by weight or more but not more than 68%, in forms as defined in note 6 (b) to chapter 39 |
| - | Synthetic poly-alpha-olefin with a viscosity of 3 or more but not more than 9 centistokes (measured at 100 ° celsius according to the astm d 445 method), obtained by polymerisation of dodecene with or without:-not more than 40% by weight of tetradecene and/or-not more than 2% by weight decene and/or-not more than 2% by weight of hexadecene |
| - | Chlorinated polyolefins, whether or not in a solution or dispersion |
| - | Other |
| 3903 | Polymers of styrene, in primary forms |
| 3903.A | Polystyrene |
| - | Expansible |
| 3903.A.A | Other |
| - | Crystalline polystyrene with:- a melting point of 268 °c or more but not more than 272 °c- a setting point of 232 °c or more but not more than 247 °c,- whether or not containing additives and filling material |
| - | Other |
| - | Styrene-acrylonitrile (san) copolymers |
| - | Acrylonitrile-butadiene-styrene (abs) copolymers |
| 3903.B | Other |
| - | Copolymer, solely of styrene with allyl alcohol, of an acetyl value of 175 or more |
| - | Brominated polystyrene, containing by weight 58% or more but not more than 71% of bromine, in one of the forms mentioned in note 6(b) to this chapter |
| 3903.B.A | Other |
| - | Copolymer in the form of granules containing by weight:- 83 ± 3% styrene,- 7 ± 2% n-butyl acrylate,- 9 ± 2% n-butyl methacrylate and- 0.01% or more but not more than 1% of polyolefinic wax |
| - | Copolymer of _α_-methylstyrene and styrene, having a softening point exceeding 113 ºc |
| - | Polytetrafluoroethylene (cas rn 9002-84-0) encapsulated with an acrylonitrile-styrene copolymer (cas rn 9003-54-7), with a content by weight of each polymer of 50% (± 1%) |
| - | Mixture of polymers consisting by weight of:-10% or more but not more than 30% of a styrene-ethylene-butylene-styrene block copolymer (cas rn 66070-58-4),-25% or more but not more than 45% of mineral oil (cas rn 8042-47-5),-25% or more but not more than 45% of calcium carbonate (cas rn 1317-65-3),-10% or more but not more than 20% of polypropylene (cas rn 9003-07-0), and-1% or more but not more than 3% of a copolymer of α-methylstyrene and vinyltoluene (cas rn 9017-27-0) |
| - | Copolymer of styrene with maleic anhydride, either partially esterified or completely chemically modified, of an average molecular weight (m@n) of not more than 4500, in flake or powder form |
| - | Copolymer of styrene with 2, 5-furandione and (1-methylethyl)benzene in the form of flakes or powder (cas rn 26762-29-8) |
| - | Copolymer in the form of granules containing by weight:- 75% (± 7%) styrene and- 25% (± 7%) methylmethacrylate |
| - | Mixture containing by weight:- 45% or more but not more than 65% of polymers of styrene,- 30% or more but not more than 45% of poly(phenylene ether), and- not more than 11% of additives |
| - | Other |
| 3904 | Polymers of vinyl chloride or of other halogenated olefins, in primary forms |
| 3904.A | Poly(vinyl chloride), not mixed with any other substances |
| 3904.A.A | In the form of granules, for use in certain types of aircraft |
| - | Suspension polyvinylchloride (‘s-pvc’), not mixed with any other substance |
| - | Other |
| 3904.A.B | Other |
| - | Suspension polyvinylchloride (‘s-pvc’), not mixed with any other substance |
| - | Other |
| 3904.B | Other poly(vinyl chloride) |
| 3904.B.A | Non-plasticised |
| - | In the form of granules, for use in certain types of aircraft |
| - | Other |
| 3904.B.B | Plasticised |
| - | In the form of granules, for use in certain types of aircraft |
| - | Other |
| - | Vinyl chloride-vinyl acetate copolymers |
| 3904.C | Other vinyl chloride copolymers |
| - | For cavity filling, for use in certain types of aircraft |
| - | Other |
| 3904.D | Vinylidene chloride polymers |
| - | Copolymer of vinylidene chloride with acrylonitrile, in the form of expansible beads of a diameter of 4 micrometres or more but not more than 20 micrometres |
| 3904.D.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| - | Other |
| 3904.E | Fluoropolymers |
| 3904.E.A | Polytetrafluoroethylene |
| - | Copolymer of tetrafluoroethylene and trifluoro(heptafluoropropoxy)ethylene, containing 3.2% or more but not more than 4.6% by weight of trifluoro(heptafluoropropoxy)ethylene and less than 1 mg/kg of extractable fluoride ions |
| - | Other |
| 3904.E.B | Other |
| - | Poly(vinyl fluoride), in one of the forms mentioned in note 6(b) to this chapter |
| - | Fluoroelastomers fkm |
| 3904.E.B.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| 3904.E.B.A.A | Other |
| - | Copolymer of tetrafluoroethylene, heptafluoro-1-pentene and ethene (cas rn 94228-79-2) |
| - | Copolymer of tetrafluoroethylene, hexafluoropropene and ethene |
| - | Copolymer of ethylene and chlorotrifluoroethylene, whether or not modified with hexafluoroisobutylene, whether or not containing fillers |
| - | Polytetrafluoroethylene (cas rn 9002-84-0) encapsulated with an acrylonitrile-styrene copolymer (cas rn 9003-54-7), with a content by weight of each polymer of 50% (± 1%) |
| - | Polychlorotrifluoroethylene, in one of the forms mentioned in note 6 (a) and (b) to chapter 39 |
| - | Copolymer of chlorotrifluoroethylene and vinylidene difluoride |
| - | Other |
| 3904.F | Other |
| - | For cavity filling, for use in certain types of aircraft |
| - | Other |
| 3905 | Polymers of vinyl acetate or of other vinyl esters, in primary forms; other vinyl polymers in primary forms |
| 3905.A | Poly(vinyl acetate) |
| - | In aqueous dispersion |
| 3905.A.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| - | Other |
| 3905.B | Vinyl acetate copolymers |
| - | In aqueous dispersion |
| 3905.B.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| - | Other |
| 3905.C | Poly(vinyl alcohol), whether or not containing unhydrolysed acetate groups |
| - | Viscous preparation, essentially consisting of poly(vinyl alcohol) (cas rn 9002-89-5), an organic solvent and water for use as protective coating of wafers during the manufacturing of semiconductors |
| 3905.C.A | Other |
| 3905.C.A.A | In the form of homopolymer resins with a viscosity (measured in 4% aqueous solution at 20 °c) of 3 mpa·s or more but not more than 61 mpa·s and a degree of hydrolysis of 80.0 mol% or more but not more than 99.9 mol%, both measured according to the iso 15023-2 method |
| - | Other than for the manufacturing of dry-blend adhesives, produced and sold in powder form for the carton board industry |
| - | Other |
| - | Other |
| 3905.D | Other |
| 3905.D.A | Copolymers |
| - | For cavity filling, for use in certain types of aircraft |
| - | Copolymer of vinylcaprolactam and vinylpyrrolidone (cas rn 51987-20-3) in the form of a solution in 2-butoxyethanol (cas rn 111-76-2) containing by weight 45% or more but not more than 58% of copolymer |
| - | Aqueous solution of a copolymer of vinylpyrrolidone and n,n-dimethylaminopropyl methacrylamide sulfate (cas rn 175893-71-7), containing by weight 8% or more, but not more than 12% of copolymer |
| - | Water soluble copolymer of ethylene and vinyl alcohol (cas rn 26221-27-2), containing by weight not more than 38% of the monomer unit ethylene |
| - | Aqueous solution consisting by weight of:-10% or more but not more than 20% of a copolymer of vinyl pyrrolidone, n,n-dimethylaminopropyl methacrylamide and 3 (methacryloylamino)propyllauryldimethylammonium chloride (cas rn 306769-73-3),-not more than 1% preservatives |
| - | Copolymer of vinylpyrrolidone, vinyl caprolactam and dimethylaminoethyl methacrylate (cas rn 102972-64-5) in solid form, or as an aqueous solution containing by weight:-27% or more but not more than 33% of copolymer,-not more than 1.5% of ethanol (cas rn 64-17-5),-not more than 1% of preservatives |
| - | Aqueous solution, containing by weight:-25% or more but not more than 35% of a copolymer of vinyl caprolactam, vinyl pyrrolidone, n,n-dimethylaminopropyl methacrylamide and 3-(methacryloylamino)propyllauryldimethylammonium chloride (cas rn 748809-45-2),-10% or more but not more than 16% of ethanol (cas rn 64-17-5) whether or not denatured with tert-butyl alcohol (cas rn 75-65-0) and/or denatonium benzoate (cas rn 3734-33-6) |
| - | Copolymer of vinylpyrrolidone, acrylic acid and dodecyl methacrylate (cas rn 83120-95-0) |
| - | Other |
| 3905.D.B | Other |
| - | Poly(vinyl formal), in one of the forms mentioned in note 6(b) to this chapter, of a molecular weight of 10 000 or more but not exceeding 40 000 and containing by weight:- 9.5% or more but not more than 13% of acetyl groups evaluated as vinyl acetate and- 5% or more but not more than 6.5% of hydroxy groups evaluated as vinyl alcohol |
| 3905.D.B.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| 3905.D.B.A.A | Other |
| - | Poly(vinyl butyral)(cas rn 63148-65-2):— containing by weight 17.5% or more, but not more than 20% of hydroxyl groups, and— with a median particle size (d50) of more than 0.6 mm |
| - | Hexadecylated or eicosylated polyvinylpyrrolidone |
| - | Polymer of vinyl formal, in one of the forms mentioned in note 6 (b) to chapter 39, of a weight average molecular weight (m@w) of 25 000 or more but not more than 150 000 and containing by weight:- 9.5% or more but not more than 13% of acetyl groups evaluated as vinyl acetate and- 5% or more but not more than 6.5% of hydroxy groups evaluated as vinyl alcohol |
| - | Povidone (inn)-iodine (cas 25655-41-8) |
| - | Poly(vinyl pyrrolidone) partially substituted by triacontyl groups, containing by weight 78% or more but not more than 82% of triacontyl groups |
| - | Other |
| 3906 | Acrylic polymers in primary forms |
| - | Poly(methyl methacrylate) |
| 3906.A | Other |
| - | Poly[n-(3-hydroxyimino-1.1-dimethylbutyl)acrylamide] |
| - | Copolymer of 2-diisopropylaminoethyl methacrylate with decyl methacrylate, in the form of a solution in n,n-dimethylacetamide, containing by weight 55% or more of copolymer |
| - | Copolymer of acrylic acid with 2-ethylhexyl acrylate, containing by weight 10% or more but not more than 11% of 2-ethylhexyl acrylate |
| - | Copolymer of acrylonitrile with methyl acrylate, modified with polybutadiene-acrylonitrile (nbr) |
| - | Polymerisation product of acrylic acid with alkyl methacrylate and small quantities of other monomers, for use as a thickener in the manufacture of textile printing pastes |
| - | Copolymer of methyl acrylate with ethylene and a monomer containing a non-terminal carboxy group as a substituent, containing by weight 50% or more of methyl acrylate, whether or not compounded with silica |
| 3906.A.A | Other |
| - | Superabsorbent polymers, insoluble in water, which result from a polymerisation of acrylic monomer molecules with crosslinkers to form crosslinked polymer networks, with a high capacity to absorb and retain water and aqueous liquids |
| - | Copolymer of methylmethacrylate, butylacrylate, glycidylmethacrylate and styrene (cas rn 37953-21-2), with an epoxy equivalent weight of not more than 500, in form of ground flakes with a particle size of not more than 1 cm |
| - | Core shell copolymer of butyl acrylate and alkyl methacrylate, with a particle size of 5 µm or more but not more than 10 µm |
| - | Copolymer of trimethylolpropane trimethacrylate and methyl methacrylate (cas rn 28931-67-1), in microsphere form with an average diameter of 3 µm |
| - | Copolymer of methacrylic esters, butylacrylate and cyclic dimethylsiloxanes (cas rn 143106-82-5) |
| - | Polymers of esters of acrylic acid with one or more of the following monomers in the chain:- chloromethyl vinyl ether,- chloroethyl vinyl ether,- chloromethylstyrene,- vinyl chloroacetate,- methacrylic acid,- butenedioic acid monobutyl ester,- butenedioic acid monocyclohexyl estercontaining by weight not more than 5% of each monomer unit |
| - | Mixture of polymers, containing by weight: -77% or more but not more than 81% of polyacrylamide (cas rn 9003-05-8), -18% or more but not more than 21% of polyethylene glycol (cas rn 25322-68-3) |
| - | Aqueous dispersion containing by weight:- more than 10% but not more than 15% of ethanol, and- more than 7% but not more than 11% of a reaction product of poly(epoxyalkylmethacrylate-co-divinylbenzene) with a glycerol derivative |
| - | Preparation containing by weight:- 33% or more but not more than 37% of butyl methacrylate - methacrylic acid copolymer,- 24% or more but not more than 28% of propylene glycol, and- 37% or more but not more than 41% of water |
| - | Other |
| 3907 | Polyacetals, other polyethers and epoxide resins, in primary forms; polycarbonates, alkyd resins, polyallyl esters and other polyesters, in primary forms |
| - | Polyacetals |
| 3907.A | Other polyethers |
| - | Bis(polyoxyethylene) methylphosphonate |
| 3907.A.A | Other |
| 3907.A.A.A | Polyether alcohols |
| 3907.A.A.A.A | Polyethylene glycols |
| - | Poly(ethylene oxide) of a number average molecular weight (m@n) of 100 000 or more |
| - | Bis[methoxypoly[ethyleneglycol)]-maleimidopropionamide, chemically modified with lysine, of a number average molecular weight (m@n) of 40 000 |
| - | Other |
| 3907.A.A.A.B | Other |
| - | Mixture containing by weight:- 5% or more but not more than 15% of a copolymer of glycerol, propylene oxide and ethylene oxide (cas rn 9082-00-2), and- 85% or more but not more than 95% of a copolymer of sucrose, propylene oxide and ethylene oxide (cas rn 26301-10-0) |
| - | Copolymer of tetrahydrofuran and tetrahydro-3-methylfuran (cas rn 38640-26-5) with a number average molecular weight (mn) of 900 or more but not more than 3 600 |
| - | 4-(1.1,3.3-tetramethylbutyl)phenol, ethoxylated |
| - | Poly(p-phenylene oxide) in the form of powder- with a glasstransitiontemperature of 210 °c or more,- with a weight average molecular weight (mw) of 35 000 or ore but not more than 80 000- with an inherent viscosity of 0.2 or more but not more than 0.6 dl/gram |
| - | 4-nonylphenol, branched and linear, ethoxylated |
| - | Other |
| 3907.A.A.B | Other |
| - | Copolymer of 1-chloro-2.3-epoxypropane with ethylene oxide |
| 3907.A.A.B.A | Other |
| - | 2.3-bis(methylpolyoxyethylene-oxy)-1-[(3-maleimido-1-oxopropyl)amino]propyloxy propane (cas rn 697278-30-1) with a number average molecular weight (mn) of at least 20 kda whether or not modified with a chemical entity enabling a linkage between the peg and a protein or a peptide |
| - | Homopolymer of 1-chloro-2.3-epoxypropane (epichlorohydrin) |
| - | Copolymer of ethylene oxide and propylene oxide, having aminopropyl and methoxy end-groups |
| - | Vinyl-silyl terminated perfluoropolyether polymer or an assortment of two components consisting of the same type of vinyl-silyl terminated perfluoropolyether polymer as the main ingredient |
| - | Succinimidyl ester of methoxy poly(ethylene glycol)propionic acid, of a number average molecular weight (mn) of 5 000 |
| - | Polytetramethylene oxide di-p-aminobenzoate |
| - | Poly(oxy-1.4-phenyleneoxy-1.4-phenylenecarbonyl-1.4-phenylene) (cas rn 29658-26-2) containing by weight not more than 35% of additives |
| - | Other |
| 3907.B | Epoxide resins |
| 3907.B.A | Epoxide resin, halogen-free,- containing by weight more than 2% phosphoros calculated on the solid content, chemically bound in the epoxide resin,- not containing any hydrolysable chloride or containing less than 300 ppm hydrolysable chloride, and- containing solventsfor use in the manufacture of prepreg sheets or rolls of a kind used for the production of printed circuits |
| - | Products containing more than 35% by weight of epoxy resins, also known as epoxide resins or polyepoxides, which are polymers or prepolymers containing reactive epoxy groups, based on epichlorohydrin (‘ech’) and an aliphatic or aromatic alcoholic component (such as bpa), in solid, semi-solid or liquid forms, having all types of grade, purity, molecule weight or molecular structure, whether or not containing modifiers, curing agents, or additives, so long as the curing agents have not chemically reacted so as to cure the epoxy resin or convert it into a different product no longer containing epoxy groups |
| - | Other |
| 3907.B.B | Epoxide resin- containing by weight 21% or more of brome,- not containing any hydrolysable chloride or containing less than 500 ppm hydrolysable chloride, and- containing solvents |
| - | Products containing more than 35% by weight of epoxy resins, also known as epoxide resins or polyepoxides, which are polymers or prepolymers containing reactive epoxy groups, based on epichlorohydrin (‘ech’) and an aliphatic or aromatic alcoholic component (such as bpa), in solid, semi-solid or liquid forms, having all types of grade, purity, molecule weight or molecular structure, whether or not containing modifiers, curing agents, or additives, so long as the curing agents have not chemically reacted so as to cure the epoxy resin or convert it into a different product no longer containing epoxy groups |
| - | Other |
| - | Epoxide resin, containing by weight 70% or more of silicon dioxide, for the encapsulation of goods of headings 8504, 8533, 8535, 8536, 8541, 8542 or 8548 |
| - | Preparation of epoxy resin (cas rn 29690-82-2) and phenolic resin (cas rn 9003-35-4) containing by weight:- 65% or more but not more than 75% of silicon dioxide (cas rn 60676-86-0), and- none or not more than 0.5% of carbon black (cas rn 1333-86-4) |
| 3907.B.C | Other |
| - | Products containing more than 35% by weight of epoxy resins, also known as epoxide resins or polyepoxides, which are polymers or prepolymers containing reactive epoxy groups, based on epichlorohydrin (‘ech’) and an aliphatic or aromatic alcoholic component (such as bpa), in solid, semi-solid or liquid forms, having all types of grade, purity, molecule weight or molecular structure, whether or not containing modifiers, curing agents, or additives, so long as the curing agents have not chemically reacted so as to cure the epoxy resin or convert it into a different product no longer containing epoxy groups |
| - | Other |
| 3907.C | Polycarbonates |
| - | Polymer blend of polycarbonate and poly(methyl methacrylate) with a polycarbonate content of 98.5% or more, in the form of pellets or granules, with a luminous transmittance of 88.5% or more, measured using a test sample with a thickness of 4 mm at a wavelength of λ = 400 nm (according to iso 13468-2) |
| - | Α-phenoxycarbonyl-ω-phenoxypoly[oxy(2.6-dibromo-1.4-phenylene) isopropylidene(3.5-dibromo-1.4-phenylene)oxycarbonyl] (cas rn 94334-64-2) |
| - | Α-(2.4,6-tribromophenyl)-ω-(2.4,6-tribromophenoxy)poly[oxy(2.6-dibromo-1.4-phenylene)isopropylidene(3.5-dibromo-1.4-phenylene)oxycarbonyl] (cas rn 71342-77-3) |
| - | Other |
| - | Alkyd resins |
| 3907.D | Poly(ethylene terephthalate) |
| - | Having a viscosity number of 78 ml/g or higher |
| 3907.D.A | Other |
| - | Copolymer of terephthalic acid and isophthalic acid with ethylene glycol, butane-1.4-diol and hexane-1.6-diol |
| - | Other |
| - | Poly(lactic acid) |
| 3907.E | Other polyesters |
| 3907.E.A | Unsaturated |
| - | Liquid |
| 3907.E.A.A | Other |
| - | Diallyl phthalate prepolymer, in powder form |
| - | Other |
| 3907.E.B | Other |
| - | Thermoplastic liquid crystal aromatic polyester copolymers |
| - | Poly(ethylene naphthalene-2.6-dicarboxylate) |
| 3907.E.B.A | Other |
| - | Copolymer, containing 72% by weight or more of terephthalic acid and/or isomers thereof and cyclohexanedimethanol |
| - | Poly(hydroxyalkanoate), predominantly consisting of poly(3-hydroxybutyrate) |
| - | Copolymer in form of a clear, pale yellow liquid, consisting of- phthalic acid isomers and/or aliphatic dicarboxylic acids,- aliphatic diols, and- fatty acid end-caps with:- a hydroxyl number of 120 mg koh or more but not more than 350 mg koh,- a viscosity at 25 °c of 2000 cps or more but not more than 8000 cps, and- an acid value less than 10 mg koh/g |
| - | Copolymer of poly(ethylene terephthalate) and cyclohexane dimethanol, containing more than 10% by weight of cyclohexane dimethanol |
| - | Copolymer, consisting of 72% by weight or more of terephthalic acid and/ or derivatives thereof and cyclohexanedimethanol, completed with linear and/ or cyclic dioles |
| - | Other |
| 3908 | Polyamides in primary forms |
| - | Polyamide-6, -11, -12, -6.6, -6.9, -6.10 or -6.12 |
| 3908.A | Other |
| - | Poly(iminomethylene-1.3-phenylenemethyleneiminoadipoyl), in one of the forms mentioned in note 6 (b) to chapter 39 |
| - | Other |
| 3909 | Amino-resins, phenolic resins and polyurethanes, in primary forms |
| - | Urea resins; thiourea resins |
| 3909.A | Melamine resins |
| - | Polymer mixture, containing by weight:- 60% or more but not more than 75% of melamine resin (cas rn 9003-08-1),- 15% or more but not more than 25% of silicon dioxide (cas rn 14808-60-7 or 60676-86-0),- 5% or more but not more than 15% of cellulose (cas rn 9004-34-6), and- 1% or more but not more than 15% of phenolic resin (cas rn 25917-04-8) |
| - | Other |
| 3909.B | Other amino-resins |
| - | Poly(methylene phenyl isocyanate) (crude mdi, polymeric mdi) |
| 3909.B.A | Other |
| - | Formaldehyde, oligomeric reaction products with aniline (cas rn 25214-70-4) |
| - | Other |
| 3909.C | Phenolic resins |
| - | Powder of thermosetting resin in which magnetic particles have been evenly distributed, for use in the manufacture of ink for photocopiers, fax machines, printers and multifunction devices |
| - | Other |
| 3909.D | Polyurethanes |
| - | Polyurethane of 2.2′-(tert-butylimino)diethanol and 4.4′-methylenedicyclohexyl diisocyanate, in the form of a solution in n,n-dimethylacetamide, containing by weight 50% or more of polymer |
| 3909.D.A | Other |
| - | Preparation containing by weight:- 14% or more but not more than 18% of ethoxylated polyurethane modified with hydrophobic groups,- 3% or more but not more than 5% of enzymatically modified starch, and- 77% or more but not more than 83% of water |
| - | Preparation containing by weight:- 16% or more but not more than 20% of ethoxylated polyurethane modified with hydrophobic groups,- 19% or more but not more than 23% of diethylene glycol butyl ether, and- 60% or more but not more than 64% of water |
| - | Preparation containing by weight:- 34% or more but not more than 36% of ethoxylated polyurethane modified with hydrophobic groups,- 37% or more but not more than 39% of propylene glycol, and- 26% or more but not more than 28% of water |
| - | Other |
| 3910 | Silicones in primary forms |
| - | Liquid poly(methylhydrosiloxane) with terminal trimethylsilyl groups (cas rn 63148-57-2) with a purity by weight of 99.9% or more |
| - | Dimethyl, methyl(propyl(polypropylene oxide)) siloxane (cas rn 68957-00-6), trimethylsiloxy-terminated |
| - | Block copolymer of poly(methyl-3.3,3-trifluoropropylsiloxane) and poly[methyl(vinyl)siloxane] |
| - | Preparations containing by weight:- 10% or more, 2-hydroxy-3-[3-[1.3,3.3-tetramethyl-1-[(trimethylsilyl)oxy] disiloxanyl] propoxy] propyl-2-methyl-2-propenoate (cas rn 69861-02-5)and- 10% or more, α-butyldimethylsilyl- ω -3-[(2-methyl-1-oxo-2-propen-1-yl)oxy]propyl-terminated silicone polymer (cas rn 146632-07-7) |
| - | Preparations containing by weight:- 30% or more, α -butyldimethylsilyl- ω -(3-methacryloxy-2-hydroxypropyloxy)propyldimethylsilyl-polydimethylsiloxane (cas rn 662148-59-6) and- 10% or more, n,n - dimethylacrylamide (cas rn 2680-03-7) |
| - | Silicones of a kind used in the manufacture of long term surgical implants |
| - | Dimethyl siloxane, hydroxy-terminated polymer with a viscosity of 38-100 mpa·s (cas rn 70131-67-8) |
| - | Silicone based pressure sensitive adhesive in solvent containing copoly(dimethylsiloxane/diphenylsiloxane) gum |
| - | Preparation containing by weight:- 55% or more but not more than 65% of vinyl terminated polydimethylsiloxane (cas rn 68083-19-2),- 30% or more but not more than 40% of dimethylvinylated and trimethylated silica (cas rn 68988-89-6), and- 1% or more but not more than 5% of silicic acid, sodium salt, reaction products with chlorotrimethylsilane and isopropyl alcohol (cas rn 68988-56-7) |
| - | Liquid copolymer based on polydimethylsiloxane with terminal epoxide groups cas rn 2102536-93-4) |
| - | Passivating silicon coating in primary form, to protect edges and prevent short circuits in semiconductor devices |
| - | Copolymer of 80% dimethylsiloxane, 10% methyl methacrylate and 10% butyl acrylate in the form of a white powder |
| - | Two-component silicone, with a viscosity of the mixture of 3 000 cps or more, but not more than 6 000 cps (according to standard gb/t 2794) for use as an electrical insulation material in solar panels junction box in the production of solar panels |
| - | Other |
| 3911 | Petroleum resins, coumarone-indene resins, polyterpenes, polysulphides, polysulphones and other products specified in note 3 to this chapter, not elsewhere specified or included, in primary forms |
| 3911.A | Petroleum resins, coumarone, indene or coumarone-indene resins and polyterpenes |
| - | For cavity filling, for use in certain types of aircraft |
| - | Non-hydrogenated hydrocarbon resin, obtained by polymerisation of more than 75% by weight c-5 to c-12 cycloaliphatic alkenes and more than 10% but not more than 25% by weight aromatic alkenes yielding a hydrocarbon resin with:- an iodine value of more than 120 and- a gardner colour of more than 10 for the pure product or- a gardner colour of more than 8 for a 50% solution by weight in toluene (as determined by the astm method d6166) |
| - | Other |
| - | Poly(1.3-phenylene methylphosphonate) |
| 3911.B | Other |
| 3911.B.A | Condensation or rearrangement polymerisation products whether or not chemically modified |
| 3911.B.A.A | Poly(oxy-1.4-phenylenesulphonyl-1.4-phenyleneoxy-1.4-phenyleneisopropylidene-1.4-phenylene), in one of the forms mentioned in note 6(b) to this chapter |
| - | Poly(oxy-1.4-phenylenesulphonyl-1.4-phenyleneoxy-1.4-phenyleneisopropylidene-1.4-phenylene) (cas rn 25135-51-7 and cas rn 25154-01-2), in one of the forms mentioned in note 6(b) to this chapter containing by weight not more than 20% of additives |
| - | Other |
| - | Poly(thio-1.4-phenylene) |
| 3911.B.A.B | Other |
| - | Polyetherimide of 4.4'-[(isopropylidene)bis(p-phenylenoxy)]diphthalic dianhydride and 1.3-benzenediamine or 1.4-benzenediamine (cas rn 61128-46-9 or cas rn 61128-47-0) |
| - | Copolymer of ethyleneimine and ethyleneimine dithiocarbamate, in an aqueous solution of sodium hydroxide |
| - | Poly(oxy-1.4-phenylenesulfonyl-1.4-phenyleneoxy-4.4’-biphenylene) (cas rns 25608-64-4 and 25839-81-0) containing by weight not more than 20% of additives |
| - | M- xylene formaldehyde resin |
| - | Poly(oxy-1.4-phenylenesulfonyl-1.4-phenylene) (cas rn 25608-63-3 and cas rn 25667-42-9) containing by weight not more than 20% of additives |
| - | Other |
| 3911.B.B | Other |
| - | Copolymer of p-cresol and divinylbenzene, in the form of a solution in n,n-dimethylacetamide containing by weight 50% or more of polymer; hydrogenated copolymers of vinyltoluene and α-methylstyrene |
| 3911.B.B.A | Other |
| - | For cavity filling, for use in certain types of aircraft |
| 3911.B.B.A.A | Other |
| - | Aqueous solution consisting of by weight 25% or more, but not more than 40% of a poly(isobutylene-maleic anhydride) modified with:-n,n-dimethylpropane-1.3-diamine,-a copolymer of ethylene oxide and propylene oxide, having aminopropyl and methoxy end-groups,-ethanol(cas rn 497926-97-3) |
| - | Copolymer of vinyltoluene and α-methylstyrene |
| - | Alternated copolymer of ethylene and maleic anhydride (ema) |
| - | Mixture containing by weight:-90% (± 1%) of 1.4:5.8- dimethanonaphthalene, 2-ethylidene-1.2,3.4,4a,5.8,8a-octahydro-,polymer with 3a,4.7,7a- tetrahydro- 4.7-methano-1h-indene, hydrogenated (cas rn 881025-72-5), and-10% (± 1%) of a hydrogenated styrene butadiene copolymer (cas rn 66070-58-4) |
| - | Mixed calcium and sodium salt of a copolymer of maleic acid and methyl vinyl ether, having a calcium content of 9% or more but not more than 16% by weight |
| - | Copolymer of α-methylstyrene and styrene, having a softening point of more than 113 ºc |
| - | Copolymer of maleic acid and methyl vinyl ether |
| - | Mixture containing by weight:-90% (± 1%) of 1.4:5.8- dimethanonaphthalene, 2-ethylidene-1.2,3.4,4a,5.8,8a-octahydro-,polymer with 3a,4.7,7a- tetrahydro- 4.7-methano-1h-indene, hydrogenated (cas rn 881025-72-5), and-10% (± 1%) of an ethylene-propylene copolymer (cas rn 9010-79-1) |
| - | Copolymer of styrene with maleic anhydride, either partially esterified or completely chemically modified, of an average molecular weight (m@n) of not more than 4500, in flake or powder form |
| - | Mixture, containing by weight: - 20% or more but not more than 40% of a copolymer of methyl vinyl ether and monobutyl maleate (cas rn 25119-68-0), - 7% or more but not more than 20% of a copolymer of methyl vinyl ether and monoethyl maleate (cas rn 25087-06-3), - 40% or more, but not more than 65% of ethanol (cas rn 64-17-5), - 1% or more but not more than 7% of butan-1-ol (cas rn 71-36-3) |
| - | Calcium zinc salt of a copolymer of maleic acid and methyl vinyl ether |
| - | Aqueous solution containing by weight:- 30% or more but not more than 40% of poly-4-vinylpyridine-n-oxide,- 0.1% or more but not more than 4% of isonicotinic acid-n-oxide,- 0.1% or more but not more than 3.5% of sodium sulphate,- 0.1% or more but not more than 2% of 4-acetylpyridine-n-oxide |
| - | Copolymer of methyl vinyl ether and maleic acid anhydride (cas rn 9011-16-9) |
| - | Other |
| 3912 | Cellulose and its chemical derivatives, not elsewhere specified or included, in primary forms |
| 3912.A | Cellulose acetates |
| 3912.A.A | Non-plasticised |
| - | Cellulose acetate flakes |
| - | Cellulose triacetate (cas rn 9012-09-3) |
| - | Cellulose diacetate powder |
| - | Other |
| - | Plasticised |
| 3912.B | Cellulose nitrates (including collodions) |
| 3912.B.A | Non-plasticised |
| - | Collodions and celloidin |
| - | Other |
| - | Plasticised |
| 3912.C | Cellulose ethers |
| - | Carboxymethylcellulose and its salts |
| 3912.C.A | Other |
| - | Hydroxypropylcellulose |
| 3912.C.A.A | Other |
| - | Ethylcellulose, not plasticised |
| - | Ethylcellulose, in the form of an aqueous dispersion containing hexadecan-1-ol and sodium dodecyl sulphate, containing by weight 27 (± 3) % of ethylcellulose |
| - | Cellulose, both hydroxyethylated and alkylated with alkyl chain-lengths of 3 or more carbon atoms |
| - | Polyquaternium 10 (cas rn 68610-92-4) |
| - | Hypromellose (inn) (cas rn 9004-65-3), for use in the manufacturing of food supplements or pharmaceuticals |
| - | Other |
| 3912.D | Other |
| 3912.D.A | Cellulose esters |
| - | Hydroxypropyl methylcellulose phthalate |
| - | Other |
| - | Other |
| 3913 | Natural polymers (for example, alginic acid) and modified natural polymers (for example, hardened proteins, chemical derivatives of natural rubber), not elsewhere specified or included, in primary forms |
| 3913.A | Alginic acid, its salts and esters |
| - | Sodium alginate extracted from brown seaweed, with- a loss on drying of not more than 15% by weight (4h at 105 °c),- a water-insoluble fraction of not more than 2% by weight, calculated on the dry weight |
| - | Other |
| 3913.B | Other |
| - | Poly(hydroxyalkanoate), predominantly consisting of poly(3-hydroxybutyrate) |
| - | Xanthan gum |
| 3913.B.A | Sodium hyaluronate |
| - | Sterile sodium hyaluronate (cas rn 9067-32-7) |
| 3913.B.A.A | Non sterile |
| - | With:- a weight average molecular weight (mw) of not more than 900 000, - an endotoxin level of not more than 0.008 endotoxin units (eu)/mg, - an ethanol content of not more than 1% by weight, - an isopropanol content of not more than 0.5% by weight |
| - | Other |
| - | Chondroitinsulphuric acid, sodium salt (cas rn 9082-07-9) |
| - | Other |
| 3914 | Ion-exchangers based on polymers of headings 3901 to 3913, in primary forms |
| - | Aqueous suspension, containing by weight-20% or more but not more than 30% of beaded agarose, modified with nitrilotriacetic acid and loaded with divalent nickel ions (cas rn 1615227-97-8), and-20% or more but not more than 30% of ethanol (cas rn 64-17-5) |
| - | Other |
| 3915 | Waste, parings and scrap, of plastics |
| 3915.A | Of polymers of ethylene |
| - | Having a specific gravity of less than 0.94 (for example, pe-ld) |
| - | Having a specific gravity of 0.94 or more (for example, pe-hd) |
| - | Of polymers of styrene |
| - | Of polymers of vinyl chloride |
| 3915.B | Of other plastics |
| - | Of polymers of propylene |
| - | Of polymers of ethylene terephthalate (for example, pet) |
| - | Other |
| 3915 | Waste, parings and scrap, of plastics |
| 3915.C | Of polymers of ethylene |
| - | Having a specific gravity of less than 0.94 (for example, pe-ld) |
| - | Having a specific gravity of 0.94 or more (for example, pe-hd) |
| - | Of polymers of styrene |
| - | Of polymers of vinyl chloride |
| 3915.D | Of other plastics |
| - | Of polymers of propylene |
| - | Of polymers of ethylene terephthalate (for example, pet) |
| - | Other |
| 3916 | Monofilament of which any cross-sectional dimension exceeds 1 mm, rods, sticks and profile shapes, whether or not surface-worked but not otherwise worked, of plastics |
| 3916.A | Of polymers of ethylene |
| - | For use in certain types of aircraft |
| - | Other |
| 3916.B | Of polymers of vinyl chloride |
| - | For use in certain types of aircraft |
| - | Other |
| 3916.C | Of other plastics |
| 3916.C.A | Of condensation or rearrangement polymerisation products, whether or not chemically modified |
| - | Rods with cellular structure, containing by weight:- polyamide-6 or poly(epoxy anhydride)- 7% or more but not more than 9% of polytetrafluorethylene if present- 10% or more but not more than 25% of inorganic fillers |
| - | Other |
| 3916.C.B | Of addition polymerisation products |
| - | For use in certain types of aircraft |
| - | Other |
| - | Other |
| 3917 | Tubes, pipes and hoses, and fittings therefor (for example, joints, elbows, flanges), of plastics |
| 3917.A | Artificial guts (sausage casings) of hardened protein or of cellulosic materials |
| - | Of hardened protein |
| - | Of cellulosic materials |
| 3917.B | Tubes, pipes and hoses, rigid |
| 3917.B.A | Of polymers of ethylene |
| 3917.B.A.A | Seamless and of a length exceeding the maximum cross-sectional dimension, whether or not surface-worked, but not otherwise worked |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.B.A.B | Other |
| - | With fittings attached, for use in civil aircraft |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.B.B | Of polymers of propylene |
| 3917.B.B.A | Seamless and of a length exceeding the maximum cross-sectional dimension, whether or not surface-worked, but not otherwise worked |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.B.B.B | Other |
| - | With fittings attached, for use in civil aircraft |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.B.C | Of polymers of vinyl chloride |
| 3917.B.C.A | Seamless and of a length exceeding the maximum cross-sectional dimension, whether or not surface-worked, but not otherwise worked |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.B.C.B | Other |
| - | With fittings attached, for use in civil aircraft |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.B.D | Of other plastics |
| 3917.B.D.A | Of addition polymerisation products |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.B.D.B | Other |
| - | With fittings attached, for use in civil aircraft |
| - | Other |
| 3917.C | Other tubes, pipes and hoses |
| 3917.C.A | Flexible tubes, pipes and hoses, having a minimum burst pressure of 27.6 mpa |
| - | With fittings attached, for use in civil aircraft |
| - | For use in certain types of aircraft |
| - | Tubings:-with an outer diameter of 0.33 mm or more but not more than 3.3 mm,-with an inner diameter of 0.01 mm or more but not more than 2.1 mm,-suitable for a maximum working pressure rate from 2.7 mpa up to 70 mpa,-suitable for all solutions used in chromatography,-whether or not with fused silica,-whether or not covered with peek,for use in chromatographic system |
| - | Other |
| 3917.C.B | Other, not reinforced or otherwise combined with other materials, without fittings |
| - | For use in certain types of aircraft |
| - | Tubings:-with an outer diameter of 0.33 mm or more but not more than 3.3 mm,-with an inner diameter of 0.01 mm or more but not more than 2.1 mm,-suitable for a maximum working pressure rate from 2.7 mpa up to 70 mpa,-suitable for all solutions used in chromatography,-whether or not with fused silica,-whether or not covered with peek,for use in chromatographic system |
| - | Heat shrinkable tube:-containing by weight 80% or more polymer,-with an insulation resistance of 90 mw or more,-with a dielectric strength of 35 kv / mm or more,-with a wall thickness of 0.04 mm or more, but not more than 0.9 mm,-with a lay-flat width of 18 mm or more, but not more than 156 mm,for use in the manufacture of aluminium electrolytic capacitors |
| - | Other |
| 3917.C.C | Other, not reinforced or otherwise combined with other materials, with fittings |
| - | With fittings attached, for use in civil aircraft |
| - | Other |
| 3917.C.D | Other |
| - | With fittings attached, for use in civil aircraft |
| 3917.C.D.A | Other |
| - | Tubings:-with an outer diameter of 0.33 mm or more but not more than 3.3 mm,-with an inner diameter of 0.01 mm or more but not more than 2.1 mm,-suitable for a maximum working pressure rate from 2.7 mpa up to 70 mpa,-suitable for all solutions used in chromatography,-whether or not with fused silica,-whether or not covered with peek,for use in chromatographic system |
| - | For use in certain types of aircraft |
| - | Other |
| 3917.D | Fittings |
| - | For use in civil aircraft |
| 3917.D.A | Other |
| - | Plastic fittings (kit of nuts and ferrules or nuts) and connectors:-threaded,-supported with or without a stainless steel ring,-suitable for a maximum working pressure rate of 2.7 mpa or more but not more than 114 mpa, for tubings with:-outer diameter of 0.33 mm or more but not more than 3.3 mm,-suitable for a maximum working pressure rate of 2.7 mpa or more but not more than 114 mpa,-suitable for all solutions used in chromatography,for use in the production of chromatographic systems |
| - | Plastic connectors containing o-rings, a retainer clip and a release system for insertion into car fuel hoses |
| - | Other |
| 3918 | Floor coverings of plastics, whether or not self-adhesive, in rolls or in the form of tiles; wall or ceiling coverings of plastics, as defined in note 9 to this chapter |
| 3918.A | Of polymers of vinyl chloride |
| 3918.A.A | Consisting of a support impregnated, coated or covered with poly(vinyl chloride) |
| - | For use in certain types of aircraft |
| - | Other |
| 3918.A.B | Other |
| - | For use in certain types of aircraft |
| - | Other |
| 3918.B | Of other plastics |
| - | For use in certain types of aircraft |
| - | Other |
| 3919 | Self-adhesive plates, sheets, film, foil, tape, strip and other flat shapes, of plastics, whether or not in rolls |
| 3919.A | In rolls of a width not exceeding 20 cm |
| 3919.A.A | Strips, the coating of which consists of unvulcanised natural or synthetic rubber |
| - | Of poly(vinyl chloride) or of polyethylene |
| - | Of polypropylene |
| 3919.A.A.A | Other |
| - | Reflecting film, consisting of a layer of polyurethane, with, on one side, security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use, and embedded glass beads and, on the other side, an adhesive layer, covered on one side or on both sides with a release film |
| - | Other |
| 3919.A.B | Other |
| - | For use in certain types of aircraft |
| 3919.A.B.A | Other |
| - | Reflecting film, consisting of a layer of polyurethane, with, on one side, security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use, and embedded glass beads and, on the other side, an adhesive layer, covered on one side or on both sides with a release film |
| - | Polyester film:- coated on one side with an acrylic thermal release adhesive that debonds at temperatures of 90 °c or more but not more than 200 °c, and a polyester liner, and- on the other side not coated or coated with an acrylic pressure sensitive adhesive or with an acrylic thermal release adhesive that debonds at temperatures of 90 °c or more but not more than 200 °c, and a polyester liner |
| - | Reflecting film, consisting of a layer of poly(vinyl chloride), a layer of alkyd polyester, with, on one side, security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use, only visible by means of a retroreflecting lighting, and embedded glass beads and, on the other side, an adhesive layer, covered on one side or on both sides with a release film |
| - | Reinforced polyethylene foam tape, coated on both sides with an acrylic micro channelled pressure sensitive adhesive and on one side a liner, with an application thickness of 0.38 mm or more but not more than 1.53 mm |
| - | Acrylic foam tape:- covered on one side with a heat activatable adhesive or an acrylic pressure sensitive adhesive, - covered on the other side with an acrylic pressure sensitive adhesive, - covered on one or both sides with a release sheet,- with a peel adhesion of more than 25 n/cm (at an angle of 90° as determined by the astm d 3330 method) |
| - | Reflecting sheet:- of a polycarbonate or acrylic polymer film embossed on one side in a regular shaped pattern- covered on one or both sides with one or more layers of plastic or metallisation, and- whether or not covered on one side with a self-adhesive layer and a release sheet |
| - | Reflecting film consisting of- a layer of an acrylic resin with imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use,- a layer of an acrylic resin having embedded glass beads,- a layer of an acrylic resin hardened by a melamine cross-linking agent,- a metal layer,- an acrylic adhesive, and- a release film |
| - | Self-adhesive reflecting sheet whether or not in segmented pieces,- whether or not containing a watermark,- with or without an application tape coated on one side with an adhesive;the reflective sheet consists of:- a layer of acrylic or vinyl polymer,- a layer of poly(methyl methacrylate) or polycarbonate containing microprisms,- a layer of metallisation,- an adhesive layer, and- a release sheet- whether or not containing an additional layer of polyester |
| - | Self adhesive reflecting film, consisting of several layers including:- a copolymer of acrylic resin,- polyurethane, - a metalised layer with, on one side, laser imprints against counterfeiting, alteration or substitution of data or duplications, or an official mark for an intended use,- glass microspheres, and- an adhesive layer, with a release liner on one or both sides |
| - | Polytetrafluoroethylene film, -with a thickness of 50 µm or more, -with a width of 6.30 mm or more but not more than 740 mm, -an elongation at break of not more than 200%, and -coated on one side with a pressure sensitive silicone adhesive with a thickness of not more than 50 µm |
| - | Other |
| 3919.B | Other |
| - | Self-adhesive circular polishing pads of a kind used for the manufacture of semiconductor wafers |
| 3919.B.A | Other |
| - | For use in certain types of aircraft |
| 3919.B.A.A | Other |
| - | Polyester film:- coated on one side with an acrylic thermal release adhesive that debonds at temperatures of 90 °c or more but not more than 200 °c, and a polyester liner, and- on the other side not coated or coated with an acrylic pressure sensitive adhesive or with an acrylic thermal release adhesive that debonds at temperatures of 90 °c or more but not more than 200 °c, and a polyester liner |
| - | Film consisting of 1 to 3 laminated layers of poly(ethylene terephthalate) and a copolymer of terephthalic acid, sebacic acid and ethylene glycol, coated on one side with an acrylic abrasion resistant coating and on the other side with an acrylic pressure sensitive adhesive, a water soluble methylcellulose coating and a poly(ethylene terephthalate) protective liner |
| - | Reflecting laminated sheet:- consisting of an epoxy acrylate layer embossed on one side in a regular shaped pattern,- covered on both sides with one or more layers of plastic material and- covered on one side with an adhesive layer and a release sheet |
| - | Reflecting sheet:- of a polycarbonate or acrylic polymer film embossed on one side in a regular shaped pattern- covered on one or both sides with one or more layers of plastic or metallisation, and- whether or not covered on one side with a self-adhesive layer and a release sheet |
| - | Reflecting film, consisting of a layer of polyurethane, with, on one side, security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use, and embedded glass beads and, on the other side, an adhesive layer, covered on one side or on both sides with a release film |
| - | Transparent poly(ethylene) self-adhesive film, free from impurities or faults, coated on one side with an acrylic pressure sensitive adhesive, with a thickness of 60 μm or more, but not more than 70 μm, and with a width of more than 1 245 mm but not more than 1 255 mm |
| - | Reinforced polyethylene foam tape, coated on both sides with an acrylic micro channelled pressure sensitive adhesive and on one side a liner, with an application thickness of 0.38 mm or more but not more than 1.53 mm |
| - | Polytetrafluoroethylene film, -with a thickness of 50 µm or more, -with a width of 6.30 mm or more but not more than 740 mm, -an elongation at break of not more than 200%, and -coated on one side with a pressure sensitive silicone adhesive with a thickness of not more than 50 µm |
| - | Reflecting laminated sheet consisting of a film of poly(methyl methacrylate) embossed on one side in a regular shaped pattern, a film of a polymer containing glass microspheres, an adhesive layer and a release sheet |
| - | Self-adhesive reflecting sheet whether or not in segmented pieces,- whether or not containing a watermark,- with or without an application tape coated on one side with an adhesive;the reflective sheet consists of:- a layer of acrylic or vinyl polymer,- a layer of poly(methyl methacrylate) or polycarbonate containing microprisms,- a layer of metallisation,- an adhesive layer, and- a release sheet- whether or not containing an additional layer of polyester |
| - | Biaxially-oriented film of poly(methyl methacrylate), of a thickness of 50μm or more but not exceeding 90μm, covered on one side with an adhesive layer and a release sheet |
| - | Acrylic foam tape:- covered on one side with a heat activatable adhesive or an acrylic pressure sensitive adhesive, - covered on the other side with an acrylic pressure sensitive adhesive, - covered on one or both sides with a release sheet,- with a peel adhesion of more than 25 n/cm (at an angle of 90° as determined by the astm d 3330 method) |
| - | Poly(vinyl chloride) film, on one side covered with- a polymer layer- an adhesive layer- a release liner, on one side embossed, containing oblate spheres;whether or not on the other side covered with an adhesive layer and a metallised polymer layer |
| - | Black polyvinyl chloride film: -with a gloss of more than 25 degrees according to astm d 2457, -whether or not covered on one side with a protective film of polyethylene terephthalate and on the other side with a micro-structured pressure sensitive acrylic adhesive and a release linerfor use in the manufacture of die-cut films for interior and exterior surfaces of cars |
| - | Transparent polyethylene film coated on one side with an aqueous acrylic adhesive, of a thickness of 30 μm to 50 μm, put up in rolls of a width of 52 cm or more but not more than 154 cm |
| - | Self-adhesive film with a thickness of 40 µm or more, but not more than 475 µm, consisting of one or more layers of transparent, metallised or dyed poly(ethylene terephthalate), covered on one side with a scratch resistant coating and on the other side with a pressure sensitive adhesive and a release liner |
| - | Self-adhesive polishing discs of microporous polyurethane, whether or not coated with a pad |
| - | Self adhesive reflecting film, consisting of several layers including:- a copolymer of acrylic resin,- polyurethane, - a metalised layer with, on one side, laser imprints against counterfeiting, alteration or substitution of data or duplications, or an official mark for an intended use,- glass microspheres, and- an adhesive layer, with a release liner on one or both sides |
| - | Reflecting film consisting of:- a polyurethane layer,- a glass microspheres layer,- a metallised aluminium layer, and- an adhesive, covered on one or both sides with a release liner,- whether or not a poly(vinyl chloride) layer,- a layer whether or not incorporating security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use |
| - | Reflector or diffuser sheets, in rolls,-for protection against ultraviolet or infra-red heat radiation, to be affixed to windows or-for equal transmission and distribution of light, intended for lcd modules |
| - | Other |
| 3920 | Other plates, sheets, film, foil and strip, of plastics, non-cellular and not reinforced, laminated, supported or similarly combined with other materials |
| 3920.A | Of polymers of ethylene |
| 3920.A.A | Of a thickness not exceeding 0.125 mm |
| 3920.A.A.A | Of polyethylene having a specific gravity of |
| 3920.A.A.A.A | Less than 0.94 |
| - | Polyethylene film, of a thickness of 20 micrometres or more but not exceeding 40 micrometres, for the production of photoresist film used in the manufacture of semiconductors or printed circuits |
| 3920.A.A.A.A.A | Stretch film, not printed |
| - | For use in certain types of aircraft |
| - | Other |
| 3920.A.A.A.A.B | Other |
| - | For use in certain types of aircraft |
| - | Other |
| 3920.A.A.A.B | 0.94 or more |
| - | For use in certain types of aircraft |
| - | Other |
| 3920.A.A.B | Other |
| - | For use in certain types of aircraft |
| 3920.A.A.B.A | Other |
| - | Tubular layered film predominately of polyethylene:- consisting of a tri-layer barrier with a core layer of ethylene vinyl alcohol covered on either side with a layer of polyamide, covered on either side with at least one layer of polyethylene,- having a total thickness of 55 µm or more,- having a diameter of 500 mm or more but not more than 600 mm |
| - | Other |
| 3920.A.B | Of a thickness exceeding 0.125 mm |
| - | Synthetic paper pulp, in the form of moist sheets made from unconnected finely branched polyethylene fibrils, whether or not blended with cellulose fibres in a quantity not exceeding 15%, containing poly(vinyl alcohol) dissolved in water as the moistening agent |
| 3920.A.B.A | Other |
| - | For use in certain types of aircraft |
| 3920.A.B.A.A | Other |
| - | Composite sheet containing an acrylic coating and laminated to a high-density polyethylene layer, of a total thickness of 0.8 mm or more but not exceeding 1.2 mm |
| - | Ethylene vinyl acetate (eva) film:- with a raised relief surface with embossed undulations,- not laminated,- not cross-linked, and- with a thickness of more than 0.3 mm |
| - | Other |
| 3920.B | Of polymers of propylene |
| 3920.B.A | Of a thickness not exceeding 0.10 mm |
| 3920.B.A.A | Biaxially oriented |
| - | For use in certain types of aircraft |
| - | Biaxialy oriented film of multiple layers of polypropylene, with a total thickness of not more than 14 micron |
| - | Other |
| 3920.B.A.B | Other |
| - | For use in certain types of aircraft |
| 3920.B.A.B.A | Other |
| - | Mono-axial oriented film, consisting of three layers, each layer consisting of a mixture of polypropylene and a copolymer of ethylene and vinyl acetate, with a core layer whether or not containing titanium dioxide, having:- a thickness of 55 µm or more but not more than 97 µm,- a tensile modulus in the machine direction of 0.30 gpa or more but not more than 1.45 gpa, and- a tensile modulus in the transverse direction of 0.20 gpa or more but not more than 0.70 gpa |
| - | Mono-axial oriented, co-extruded film:-consisting of 3 to 5 layers,-each layer mainly consisting of polypropylene and/or polyethylene,-each layer containing not more than 10% by weight of other polymers,-whether or not containing titanium dioxide in the core layer,-of an overall thickness of not more than 75 μm |
| - | Other |
| 3920.B.B | Of a thickness exceeding 0.10 mm |
| - | For use in certain types of aircraft |
| - | Other |
| 3920.C | Of polymers of styrene |
| - | Acrylonitrile-butadiene-styrene, for use in certain types of aircraft |
| - | Other |
| 3920.D | Of polymers of vinyl chloride |
| 3920.D.A | Containing by weight not less than 6% of plasticisers |
| 3920.D.A.A | Of a thickness not exceeding 1 mm |
| - | For use in certain types of aircraft |
| 3920.D.A.A.A | Other |
| - | Sheeting of poly(vinyl chloride), stabilised against ultraviolet rays, without any holes, even microscopic, of a thickness of 60 µm or more but not more than 80 µm, containing 30 or more but not more than 40 parts of plasticizer to 100 parts of poly(vinyl chloride) |
| - | Reflecting laminated sheet, consisting of a film of poly(vinyl chloride) and a film of an other plastic totally embossed in a regular pyramidal pattern, covered on one side with a release sheet |
| - | Other |
| 3920.D.A.B | Of a thickness exceeding 1 mm |
| - | For use in certain types of aircraft |
| - | Other |
| 3920.D.B | Other |
| 3920.D.B.A | Of a thickness not exceeding 1 mm |
| - | For use in certain types of aircraft |
| 3920.D.B.A.A | Other |
| - | Film of a (polyvinyl)chloride-copolymer- containing by weight 45% or more of fillers- on a support |
| - | Other |
| 3920.D.B.B | Of a thickness exceeding 1 mm |
| - | For use in certain types of aircraft |
| - | Other |
| 3920.E | Of acrylic polymers |
| 3920.E.A | Of poly(methyl methacrylate) |
| - | Plate of poly(methyl methacrylate) containing aluminium trihydroxide, of a thickness of 3.5 mm or more but not more than 19 mm |
| - | Biaxially-oriented film of poly(methyl methacrylate), of a thickness of 50μm or more but not exceeding 125μm |
| - | Sheets of polymethylmethacrylate conforming to standard en 4366 (mil-prf-25690) |
| - | Sheets of polymethylmethacrylate conforming to standard— en 4364 (mil-p-5425e) and dtd5592a, or— en 4365 (mil-p-8184) and dtd5592a |
| - | Other |
| 3920.E.B | Other |
| - | Copolymer of acrylic and methacrylic esters, in the form of film of a thickness not exceeding 150 micrometres |
| - | Other |
| 3920.F | Of polycarbonates, alkyd resins, polyallyl esters or other polyesters |
| 3920.F.A | Of polycarbonates |
| - | Reflecting sheet:- of a polycarbonate or acrylic polymer film embossed on one side in a regular shaped pattern- covered on one or both sides with one or more layers of plastic or metallisation, and- whether or not covered on one side with a self-adhesive layer and a release sheet |
| - | Extruded thermoplastic foils or films of polycarbonate with: - matt surface texture on both sides - a thickness of more than 50 mm but not more than 200 mm, - a width of 800 mm or more, but not more than 1 500 mm, and - a length of 300 m or more, but not more 2500 m |
| - | Coextruded film of polycarbonate main layer and polymethyl methacrylate top layer with a:-total thickness of more than 230 μm but not more than 270 μm,-top layer thickness of more than 40 μm but not more than 55 μm,-defined surface roughness of the top layer of 0.5 μm or less (according to iso 4287),-uv-stabilised top layer |
| - | Other |
| 3920.F.B | Of poly(ethylene terephthalate) |
| 3920.F.B.A | Of a thickness not exceeding 0.35 mm |
| - | Poly(ethylene terephthalate) film, of a thickness of 72 micrometres or more but not exceeding 79 micrometres, for the manufacture of flexible magnetic disks; poly(ethylene terephthalate) film, of a thickness of 100 micrometres or more but not exceeding 150 micrometres, for the manufacture of photopolymer printing plates |
| 3920.F.B.A.A | Other |
| - | Poly(ethylene terephthalate) film in rolls:- with a thickness of 0.335 mm or more but not more than 0.365 mm, and- coated with a gold layer with a thickness of 0.03 μm or more but not more than 0.06 μm |
| - | Poly(ethylene terephthalate) film, not coated with an adhesive, of a thickness of not more than 25 µm, either:- only dyed in the mass, or- dyed in the mass and metallised on one side |
| - | Non-transparent poly(ethylene terephthalate) film:-each outer layer with a thickness of 7 nm or more but not more than 80 nm,-with a tensile strength of 300 n/cm or more (astm d-882),-with a total thickness of 200 µm or more but not more than 350 µm, and-with a width of 600 mm or more but not more than 1 600 mm- covered on one side with a layer of a fluoropolymer, and on the other side with an adhesive and a layer of polyvinylidene difluoride, or coated on both sides with polyvinylidene difluoride or polyvinyl fluoride based on fluorinated polymer composites |
| - | Transparent poly(ethylene terephthalate) film:-having thickness of both sides of 7 nm or more but not more than 80 nm, or thickness of both sides of 7 µm or more but not more than 80 µm, whether coated with an acrylic-based organic material or not,-with a surface tension of 36 dyne/cm or more but not more than 39 dyne/cm, or transparent 3 or 4 layers, second layer of pet, and other layers contain fluorine resin, -with a light transmittance of more than 70%, -with a haze value of not more than 1.3%,-with a total thickness of 10 µm or more but not more than 350 µm, -with a width of 800 mm or more but not more than 1 600 mm |
| - | Poly(ethylene terephthalate) film, of a thickness of not more than 12 µm, coated on one side with a layer of aluminium oxide of a thickness of not more than 35 nm |
| - | Sheets or rolls of poly(ethylene terephthalate):- coated on both sides with a layer of epoxy acrylic resin,- of a total thickness of 37 μm (± 3 μm) |
| - | Film of poly(ethylene terephthalate), poly(ethylene naphthalate) or similar polyester, coated on one side with metal and/or metal oxides, containing by weight less than 0.1% of aluminium, of a thickness of not more than 300 µm and having a surface resistivity of not more than 10 000 ohms (per square) (as determined by the astm d 257 method) |
| - | Poly (ethylene terephtalate) film:- of a thickness of not more than 20 µm,- coated on at least one side with a gas barrier layer consisting of a polymeric matrix in which silica or aluminium oxide has been dispersed and of a thickness of not more than 2µm |
| - | Poly(ethylene terephthalate) film in rolls:-with a thickness of 50 μm or more but not more than 350 μm, and-covered with a layer of sputtered precious metal such as gold or palladium with a thickness of 0.02 μm or more but not more than 0.06 μm |
| - | Other |
| 3920.F.B.B | Of a thickness exceeding 0.35 mm |
| - | Poly(ethylene terephthalate) film in rolls:- with a thickness of 0.335 mm or more but not more than 0.365 mm, and- coated with a gold layer with a thickness of 0.03 μm or more but not more than 0.06 μm |
| - | Poly(ethylene terephthalate) film in rolls:-with a thickness of 50 μm or more but not more than 350 μm, and-covered with a layer of sputtered precious metal such as gold or palladium with a thickness of 0.02 μm or more but not more than 0.06 μm |
| - | Other |
| - | Of unsaturated polyesters |
| 3920.F.C | Of other polyesters |
| - | Film of poly(ethylene naphthalene-2.6-dicarboxylate) |
| - | Mono- or multilayer, transverse oriented, shrink film:-composed of more than 85% by weight of polylactic acid, not more than 5% by weight of inorganic or organic additives and not more than 10% by weight of additives based on biodegradable polyesters,-with a thickness of 20 μm or more but not more than 100 μm,-with a length of 2 385 m or more but not more than 9 075 m,-biodegradable and compostable (as determined by the method en 13432) |
| - | Mono- or multilayer, biaxially oriented film: -composed of more than 85% by weight of polylactic acid, not more than 5% by weight of inorganic or organic additives, and not more than 10% by weight of additives based on biodegradable polyesters, -with a thickness of 9 mm or more but not more than 120 mm, -with a length of 1 395 m or more but not more than 21 560 m, -biodegradable and compostable (as determined by the method en 13432) |
| - | Other |
| 3920.G | Of cellulose or its chemical derivatives |
| - | Of regenerated cellulose |
| 3920.G.A | Of cellulose acetate |
| - | Film in rolls or in strips, for cinematography or photography |
| - | Other |
| 3920.G.B | Of other cellulose derivatives |
| - | Of vulcanised fibre |
| - | Other |
| 3920.H | Of other plastics |
| 3920.H.A | Of poly(vinyl butyral) |
| - | For use in certain types of aircraft |
| 3920.H.A.A | Other |
| - | Poly(vinyl butyral) film:- containing by weight 26% or more but not more than 30% of triethyleneglycol bis(2-ethyl hexanoate) as a plasticiser,- with a thickness of 0.73 mm or more but not more than 1.50 mm |
| - | Poly(vinyl butyral) film having a graduated coloured band |
| - | Film of poly(ethylene terephthalate), whether or not metallised on one or both sides, or laminated film of poly(ethylene terephthalate) films, metallised on the external sides only, and having the following characteristics:- a visible light transmission of 50% or more,- coated on one or both sides with a layer of poly(vinyl butyral) but not coated with an adhesive or any other material except poly(vinyl butyral),- a total thickness of not more than 0.2 mm without taking the presence of poly(vinyl butyral) into account and a thickness of poly(vinyl butyral) of more than 0.2 mm |
| 3920.H.A.A.A | Co-extruded trilayer poly(vinyl butyral) film |
| - | Co-extruded trilayer poly(vinyl butyral) film with a graduated colour band containing by weight 29% or more but not more than 31% of 2.2'-ethylenedioxydiethyl bis(2-ethylhexanoate) as a plasticiser |
| - | Other |
| - | Other |
| - | Of polyamides |
| - | Of amino-resins |
| - | Of phenolic resins |
| 3920.H.B | Of other plastics |
| 3920.H.B.A | Of condensation or rearrangement polymerisation products, whether or not chemically modified |
| - | Polyimide foil and strip, uncoated, or coated or covered solely with plastic |
| 3920.H.B.A.A | Other |
| - | Polymer film containing the following monomers:- poly (tetramethylene ether glycol),- bis (4-isocyanotocyclohexyl) methane,- 1.4-butanediol or 1.3-butanediol,- with a thickness of 0.25 mm or more but not more than 5.0 mm,- embossed with a regular pattern on one surface,- and covered with a release sheet |
| - | Thermoplastic polyurethane foil in rolls, with:-a width of 900 mm or more but not more than 1016 mm,-a matt finish,-a thickness of 0.4 mm (± 8%),-an elongation at break of 480% or more (astm d412 (die c)),-a tensil strength in machine direction of 470 (± 10) kg/cm² (astm d412 (die c)),-a shore a hardness of 90 (± 3) (astm d2240),-a tear strength of 100 (± 10) kg/cm² (astm d624 (die c)),-a melting point of 165°c (± 10 °c) |
| - | Thermoplastic polyurethane film, of a thickness of 250 μm or more but not more than 350 μm, covered on one side with a removable protective film |
| - | Matt, thermoplastic polyurethane foil in rolls with:- a width of 1640 mm (± 10 mm),- a gloss of 3.3 degrees or more but not more than 3.8 (as determined by the method astm d2457),- a surface roughness of 1.9 ra or more but not more than 2.8 ra (as determined by the method iso 4287),- a thickness of more than 365 µm but not more than 760 µm,- a hardness of 90 (± 4) (as determined by the method: shore a (astm d2240)),- an elongation to break of 470% (as determined by the method: en iso 527) |
| - | Sheets on rolls, consisting of epoxy resin, with conducting properties, containing:- microspheres with a coating of metal, whether or not alloyed with gold,- an adhesive layer,- with a protective layer of silicone or poly(ethylene terephthalate) on one side, - with a protective layer of poly(ethylene terephthalate) on the other side, and- with a width of 5 cm or more but not more than 100 cm- with a length of not more than 2 000 m |
| - | Other |
| 3920.H.B.B | Of addition polymerisation products |
| - | Poly(vinyl fluoride) sheet; biaxially oriented poly(vinyl alcohol) film, containing by weight 97% or more of poly(vinyl alcohol), uncoated, of a thickness not exceeding 1 mm |
| - | Ion-exchange membranes of fluorinated plastic material, for use in chlor-alkali electrolytic cells |
| 3920.H.B.B.A | Other |
| - | For use in certain types of aircraft |
| 3920.H.B.B.A.A | Other |
| - | Poly(1-chlorotrifluoroethylene) film |
| - | Film of a vinyl alcohol copolymer, soluble in cold water, of a thickness of 34 µm or more but not more than 90 µm, a tensile strength at break of 20 mpa or more but not more than 55 mpa and an elongation at break of 250% or more but not more than 900% |
| - | Other |
| - | Other |
| 3921 | Other plates, sheets, film, foil and strip, of plastics |
| 3921.A | Cellular |
| 3921.A.A | Of polymers of styrene |
| - | Acrylonitrile butadiene styrene, for use in certain types of aircraft |
| - | Other |
| 3921.A.B | Of polymers of vinyl chloride |
| - | For use in certain types of aircraft |
| - | Other |
| 3921.A.C | Of polyurethanes |
| - | Flexible |
| - | Other |
| 3921.A.D | Of regenerated cellulose |
| - | Cellular block of regenerated cellulose, impregnated with water containing magnesium chloride and quaternary ammonium compounds, measuring 100 cm (± 10 cm) × 100 cm (± 10 cm) × 40 cm (± 5 cm) |
| - | Other |
| 3921.A.E | Of other plastics |
| - | For use in certain types of aircraft |
| 3921.A.E.A | Other |
| - | Blocks with cellular structure, containing by weight:- polyamide-6 or poly(epoxy anhydride)- 7% or more but not more than 9% of polytetrafluorethylene if present- 10% or more but not more than 25% of inorganic fillers |
| - | Transparent, microporous, acrylic acid grafted polyethylene film, in the form of rolls, with:- a width of 98 mm or more but not more than170 mm,- a thickness of 15 µm or more but not more than 36 µm,of a kind used for the manufacture of alkaline battery separators |
| - | Microporous monolayer film of polypropylene or a microporous trilayer film of polypropylene, polyethylene and polypropylene, each film with:-zero transversal production direction (td) shrinkage,-a total thickness of 8 μm or more, but not more than 50 μm,-a width of 15 mm or more, but not more than 900 mm,-a length of more than 200 m, but not more than 8 000 m,-an average pore size between 0.02 μm and 0.1 μm-laminated or not with a polypropylene non-woven mat of 50 to 200 µm thickness-coated or not with surfactant-coated or not on 1 or 2 sides with a ceramic layer of min 1 µm thickness or more, but not more than 5 µm-coated or not on 1 or 2 sides with a sticky binder, pvdf type or similar of min 0.5 µm thickness or more, but not more than 5 µm |
| - | Porous membrane of polytetrafluorethylene (ptfe) laminated to a polyester spunbonded non-woven cloth with- a total thickness of more than 0.05 mm but not more than 0.20 mm,- a water entry pressure between 5 and 200 kpa according to iso 811, and- an air permeability of 0.08 cm3/cm2/s or more according to iso 5636-5 |
| - | Multi-porous multilayer separator foil with:- one microporous polyethylene layer between two microporous polypropylene layers and whether or not containing a coating of aluminium oxide on both sides,- a width of 65 mm or more but not more than 170 mm,- a total thickness of 0.01 mm or more but not more than 0.03 mm,- a porosity of 0.25 or more but not more than 0.65 |
| - | Film of polyethersulfone, of a thickness of not more than 200 µm |
| - | Other |
| 3921.B | Other |
| 3921.B.A | Of condensation or rearrangement polymerisation products, whether or not chemically modified |
| 3921.B.A.A | Of polyesters |
| - | Corrugated sheet and plates |
| - | Composite plate of poly(ethylene terephthalate) or of poly(butylene terephthalate), reinforced with glass fibres |
| - | Multilayer film consisting of:- a poly(ethylene terephthalate) film with a thickness of more than 100 µm but not more than 150 µm,- a primer of phenolic material with a thickness of more than 8 µm but not more than 15 µm,- an adhesive layer of a synthetic rubber with a thickness of more than 20 µm but not more than 30 µm,- and a transparent poly(ethylene terephthalate) liner with a thickness of more than 35 µm but not more than 40 µm |
| - | Other |
| - | Of phenolic resins |
| 3921.B.A.B | Of amino-resins |
| 3921.B.A.B.A | Laminated |
| - | High-pressure laminates with a decorative surface on one or both sides |
| - | Other |
| - | Other |
| 3921.B.A.C | Other |
| - | Prepreg sheets or rolls containing polyimide resin |
| - | Glass fibre impregnated with epoxy resin for use in the manufacture of smart cards |
| - | Three layered fabric sheet, in rolls,- comprising a core layer of 100% nylon taffeta or nylon/polyester blended taffeta,- coated on both sides with polyamide ,- of a total thickness not more than 135 μm,- of a total weight not more than 80 g/m2 |
| - | Membrane composed of a polyamide layer and a polysulfone layer on a polyethylene terephthalate support layer with:-a total thickness of 0.25 mm or more but not more than 0.40 mm,-a total weight of 109 g/m² or more but not more than 114 g/m² |
| - | Other |
| 3921.B.B | Of addition polymerisation products |
| - | For use in certain types of aircraft |
| - | Other |
| - | Other |
| 3922 | Baths, shower-baths, sinks, washbasins, bidets, lavatory pans, seats and covers, flushing cisterns and similar sanitary ware, of plastics |
| - | Baths, shower-baths, sinks and washbasins |
| - | Lavatory seats and covers |
| - | Other |
| 3923 | Articles for the conveyance or packing of goods, of plastics; stoppers, lids, caps and other closures, of plastics |
| 3923.A | Boxes, cases, crates and similar articles |
| - | Boxes, cases, crates and similar articles, of plastic, specially shaped or fitted for the conveyance or packing of semiconductor wafers, masks, or reticles |
| 3923.A.A | Other |
| - | Photomask or wafer compacts:- consisting of antistatic materials or blended thermoplastics proving special electrostatic discharge (esd) and outgassing properties,- having non porous, abrasion resistant or impact resistant surface properties,- fitted with a specially designed retainer system that protects the photomask or wafers from surface or cosmetic damage and- with or without a gasket seal,of a kind used in the photolithography or other semiconductor production to house photomasks or wafers |
| - | Other |
| 3923.B | Sacks and bags (including cones) |
| - | Of polymers of ethylene |
| 3923.B.A | Of other plastics |
| - | Of poly(vinyl chloride) |
| - | Other |
| 3923.C | Carboys, bottles, flasks and similar articles |
| - | Of a capacity not exceeding two litres |
| - | Of a capacity exceeding two litres |
| 3923.D | Spools, cops, bobbins and similar supports |
| - | Spools, reels and similar supports for photographic and cinematographic film or for tapes, films and the like of heading 8523 |
| - | Other |
| 3923.E | Stoppers, lids, caps and other closures |
| - | Caps and capsules for bottles |
| - | Other |
| - | Other |
| 3924 | Tableware, kitchenware, other household articles and hygienic or toilet articles, of plastics |
| 3924.A | Tableware and kitchenware |
| 3924.A.A | Kitchenware containing polyamide or melamine |
| - | Consigned from China or Hong Kong |
| - | Other |
| - | Polycarbonate infant feeding bottles |
| - | Other |
| 3924.B | Other |
| - | Ironing boards, including sleeve boards, whether or not free standing, and legs and tops thereof |
| - | Other |
| 3925 | Builders' ware of plastics, not elsewhere specified or included |
| - | Reservoirs, tanks, vats and similar containers, of a capacity exceeding 300 litres |
| - | Doors, windows and their frames and thresholds for doors |
| - | Shutters, blinds (including venetian blinds) and similar articles and parts thereof |
| 3925.A | Other |
| - | Fittings and mountings intended for permanent installation in or on doors, windows, staircases, walls or other parts of buildings |
| - | Trunking, ducting and cable trays for electrical circuits |
| - | Other |
| 3926 | Other articles of plastics and articles of other materials of headings 3901 to 3914 |
| - | Office or school supplies |
| - | Articles of apparel and clothing accessories (including gloves, mittens and mitts) |
| 3926.A | Fittings for furniture, coachwork or the like |
| - | Plastic internal door handle used in the manufacture of motor vehicles |
| - | Coated interior or exterior decorative parts consisting of:-a copolymer of acrylonitrile-butadiene-styrene (abs), whether or not mixed with polycarbonate, and-a pvc foil,-not containing layers of copper, nickel or chromium,for use in the manufacturing of parts for motor vehicles of heading 8701 to 8705 |
| - | Other |
| - | Statuettes and other ornamental articles |
| 3926.B | Other |
| - | Perforated buckets and similar articles used to filter water at the entrance to drains |
| - | Protective face shields/visors |
| 3926.B.A | Other |
| - | For technical uses, for use in civil aircraft |
| - | Microspheres of a polymer of divinylbenzene, of a diameter of 4.5 µm or more but not more than 80 µm |
| - | Gaskets for road vehicles mirrors and their components, made of polyethylene foam, produced by a thermoforming process and with:-a density of 20 kg/m³ or more, but not more than 40 kg/m³,-a tensile strength of not less than 170 kpa,-water absorption coefficient of not greater than 1%,-a length of 5 mm or more but not more than 300 mm,-a height of 10 mm or more but not more than 400 mm,-a depth of 5 mm or more but not more than 250 mm |
| - | Plastic cover with clips for the exterior rear-view mirror of motor vehicles |
| - | Gasket of polyethylene foam, intended to fill-up the space between the body of a motor vehicle and the base of a rear-view mirror |
| - | Parts of car radio and car air-conditioner front panels- of acrylonitrile-butadiene-styrene with or without polycarbonate,- coated with a copper, a nickel and a chrome layers,- with a total thickness of coating of 5.54 μm or more but not more than 49.6 μm |
| - | Housings, housing parts, drums, setting wheels, frames, covers, upper part, design plate and other parts of acrylonitrile-butadiene-styrene, polycarbonate, polymethylmethacrylate or thermoplastic polyurethane, of a kind used for the manufacture of remote controls |
| - | Silicone shell for breast implant |
| - | Mixture of water and by weight 19% or more but not more than 35% of expanded hollow microspheres of a copolymer of acrylonitrile, methacrylonitrile and isobornyl methacrylate or other methacrylate, of a diameter of 3 µm or more but not more than 4.95 μm |
| - | Coated interior or exterior decorative parts consisting of:-a copolymer of acrylonitrile-butadiene-styrene (abs), whether or not mixed with polycarbonate, and-a pvc foil,-not containing layers of copper, nickel or chromium,for use in the manufacturing of parts for motor vehicles of heading 8701 to 8705 |
| - | Plastic ferrules and/or plugs:-supported with or without a stainless steel ring,-suitable for a maximum working pressure rate of 2.7 mpa or more but not more than 114 mpa,for tubings with:-outer diameter of 0.33 mm or more but not more than 3.3 mm,-suitable for a maximum working pressure rate of 2.7 mpa or more but not more than 114 mpa,-suitable for all solutions used in chromatography,for use in the production of chromatographic systems |
| - | Sheath contraceptives of polyurethane |
| - | Silicone decoupling ring with an inner diameter of 14.7mm or more but no more than 16.0mm, in immediate packings of 2 500 pieces or more, of a kind used in car parking aid sensor systems |
| - | Other |
Need help to the find appropriate HS Code ?
or