HS Codes - 72: Iron and steel

I. Primary materials; products in granular or powder form

Non-alloy pig iron containing by weight 0,5 % or less of phosphorus

Containing by weight 1 % or less of silicon

Other

Containing by weight not less than 0,1 % but less than 0,4 % of manganese

Other

Non-alloy pig iron containing by weight more than 0,5 % of phosphorus

Alloy pig iron containing by weight not less than 0,3 % but not more than 1 % of titanium and not less than 0,5 % but not more than 1 % of vanadium

Ferro-alloys

Containing by weight more than 2 % of carbon

Other

Ferro-silicon

Other

Other

Ferro-chromium

Containing by weight more than 4 % but not more than 6 % of carbon

Other

Containing by weight more than 30 % but not more than 90 % of chromium (super-refined ferrochromium)

Containing by weight more than 0,05 % but not more than 0,5 % of carbon

Containing by weight not more than 0,1 % of carbon and more than 30 % but not more than 90 % of chromium (super-refined ferrochromium)

Other

Ferro-silico-chromium

Ferro-molybdenum

Other

Ferro-vanadium

Other

Ferro-silico-magnesium

Ferro-dysprosium, containing by weight: , - 78 % or more of dysprosium and , , - 18 % or more but no more than 22 % of iron

Other

Ferrous products obtained by direct reduction of iron ore

Ferrous waste and scrap; remelting scrap ingots of iron or steel

Waste and scrap of alloy steel

Containing by weight 8 % or more of nickel

Other

Scrap

Other

Other

Scrap

Other waste and scrap

Turnings, shavings, chips, milling waste, sawdust and filings

Other

In bundles

Other

Scrap

Other

Scrap

Other

Scrap

Other

Other

Granules and powders, of pig iron, spiegeleisen, iron or steel

Powders

Other

Iron and non-alloy steel in ingots or other primary forms (excluding iron of heading 7203)

Other

Containing by weight less than 0,25 % of carbon

Rolled or obtained by continuous casting

Other

Of a thickness exceeding 130 mm

Other, of rectangular (other than square) cross-section

Forged

Of circular or polygonal cross-section

Forged

Blanks for angles, shapes and sections, rolled or obtained by continuous casting

Containing by weight 0,25 % or more of carbon

Rolled or obtained by continuous casting

Other, containing by weight

0,6 % or more of carbon

Other, of rectangular (other than square) cross-section

Forged

Rolled or obtained by continuous casting

Other

Other

In coils, not further worked than hot-rolled, with patterns in relief

Of a thickness of 4,75 mm or more

Of a thickness of less than 3 mm

Of a thickness exceeding 10 mm

Intended for re-rolling

Of a thickness of 3 mm or more but less than 4,75 mm

Other

Intended for re-rolling

Not in coils, not further worked than hot-rolled, with patterns in relief

Of a thickness of less than 2 mm

Of a thickness exceeding 10 mm

Of non-alloy steel, excluding tool steel

Of a thickness exceeding 10 mm but not exceeding 15 mm, of a width of

Of non-alloy steel, excluding tool steel

Less than 2 050 mm

Other

Rolled on four faces or in a closed box pass, of a width not exceeding 1 250 mm

2 050 mm or more

Other

Of a thickness of 3 mm or more but less than 4,75 mm

Other

Other

Of non-alloy steel, excluding tool steel, of a thickness exceeding 10 mm or of a thickness of 4,75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more

Other

Of non-alloy steel, excluding tool steel, of a thickness exceeding 10 mm or of a thickness of 4,75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more

Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated

Of a thickness of 3 mm or more

Other

'Electrical'

Of a thickness of 0,5 mm or more but not exceeding 1 mm

Other

'Electrical'

Of a thickness of 0,35 mm or more but less than 0,5 mm

Annealed (known as 'black plates')

Not in coils, not further worked than cold-rolled (cold-reduced)

'Electrical'

Of a thickness exceeding 1 mm but less than 3 mm

Other

'Electrical'

Of a thickness of less than 0,5 mm

Other

Perforated

Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)

Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated

Of a thickness of 0,5 mm or more

Other

Tinplate

Other

Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)

Plated or coated with lead, including terne-plate

Other

Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)

Otherwise plated or coated with zinc

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)

Plated or coated with aluminium

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Tinplate, varnished; products, plated or coated with chromium oxides or with chromium and chromium oxides, varnished

Other

Not further worked than surface-treated or simply cut into shapes other than rectangular (including square)

Other

Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding so-called 'sandwich panels' of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, and excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin

Other

Not further worked than surface-treated, including cladding, or simply cut into shapes other than rectangular (including square)

Tinned and printed

Other

Silvered, gilded, platinium-plated or enamelled

Not further worked than surface-treated, including cladding, or simply cut into shapes other than rectangular (including square)

Other

Not further worked than hot-rolled

Of a width not exceeding 350 mm and of a thickness of 50 mm or more

Other, of a thickness of 4,75 mm or more

Of a width not exceeding 500 mm

Other

Of a width exceeding 500 mm

Of a width not exceeding 350 mm and of a thickness of 50 mm or more

Not further worked than cold-rolled (cold-reduced)

'Electrical'

Of a width not exceeding 500 mm

Of a thickness of 0,35 mm or more

Of a width not exceeding 500 mm

Other

Of a width exceeding 500 mm

Other

In coils intended for the manufacture of tinplate

Other

In coils, annealed (known as 'black plates')

Other

'Electrical'

Of a width not exceeding 500 mm

Other

Perforated

Of a width exceeding 500 mm

Other

Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, clad, plated or coated

Tinplate, not further worked than surface-treated

Of a width exceeding 500 mm

Other

Electrolytically plated or coated with zinc

Not further worked than surface-treated

Of a width not exceeding 500 mm

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Tinplate, not further worked than varnished; products, plated or coated with chromium oxides or with chromium and chromium oxides, varnished

Other

Not further worked than surface-treated

Of a width not exceeding 500 mm

Of a width exceeding 500 mm

Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70 % or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin

Other

Other

Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding so-called 'sandwich panels' of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, and excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc)

Otherwise plated or coated

Of a width exceeding 500 mm

Other

Plated or coated with chromium or nickel

Not further worked than surface-treated

Of a width not exceeding 500 mm

Of a width exceeding 500 mm

Other

Plated or coated with aluminium

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Of a width exceeding 500 mm

Other

Plated or coated by hot dip galvanisation with magnesium or magnesium-zinc alloys, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0,5% of carbon, not more than 1,1% of aluminium, not more than 0,12% of niobium, not more than 0,17% of titanium and not more than 0,15% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Of a width not exceeding 500 mm

Other

Of a width exceeding 500 mm

Other

Not further worked than surface-treated

Other

Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel

Other, of free-cutting steel

Of circular cross-section measuring less than 14 mm in diameter

Of a type used for tyre cord

Containing by weight 0,06 % or less of carbon

Containing by weight 0,25 % or more but not more than 0,75 % of carbon

Other

Containing by weight 0,25 % or more of carbon

Forged

Other

High fatigue performance concrete reinforcing bars and rods

Concrete reinforcement bars and rods excluding long products, such as round bars

Other, of free-cutting steel

Other

Of rectangular (other than square) cross-section

Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars

Containing by weight 0,25 % or more of carbon

Other

Containing by weight less than 0,25 % of carbon

Bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance bars and rods, and excluding other long products, such as round bars

Other, of circular cross-section measuring in diameter

Less than 80 mm

Containing by weight 0,25 % or more of carbon

80 mm or more

Other

Other

Of free-cutting steel, not further worked than cold-formed or cold-finished

Containing by weight less than 0,25 % of carbon

Other

Other

Other

U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm

L sections

U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more

Of a height of 80 mm or more but not exceeding 220 mm

I sections

With parallel flange faces

Of a height exceeding 220 mm

Other

Of a height of 80 mm or more but not exceeding 180 mm

L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more

T sections

With a cross-section which is capable of being enclosed in a square the side of which is 80 mm

Bulb flats

Other

Angles, shapes and sections, not further worked than cold-formed or cold-finished

C, L, U, Z, omega or open-ended sections

Other

Cold-formed or cold-finished from flat-rolled products

Other

Hot-rolled, hot-drawn or extruded, not further worked than clad

Wire of iron or non-alloy steel

Containing by weight less than 0,25 % of carbon

With a maximum cross-sectional dimension of 0,8 mm or more

Other

Containing by weight 0,6 % or more of carbon

Other

Containing by weight less than 0,25 % of carbon

With a maximum cross-sectional dimension of 0,8 mm or more

Containing by weight 0,6 % or more of carbon

Other

Containing by weight less than 0,25 % of carbon

Other

Containing by weight 0,6 % or more of carbon

Containing by weight less than 0,25 % of carbon

Containing by weight 0,6 % or more of carbon

Stainless steel in ingots or other primary forms; semi-finished products of stainless steel

Other

Containing by weight 2,5 % or more of nickel

Other

Rolled or obtained by continous casting

Other

Forged

Not further worked than hot-rolled, in coils

Consigned from Türkiye

Of a thickness of 4,75 mm or more but not exceeding 10 mm

Consigned from Türkiye

Containing by weight less than 2,5 % of nickel

Other

Containing by weight 2,5 % or more of nickel

Other

Consigned from Türkiye

Of a thickness of less than 3 mm

Consigned from Türkiye

Containing by weight less than 2,5 % of nickel

Other

Of a thickness exceeding 10 mm

Containing by weight less than 2,5 % of nickel

Containing by weight 2,5 % or more of nickel

Other

Consigned from Türkiye

Of a thickness of 3 mm or more but less than 4,75 mm

Other

Consigned from Türkiye

Not further worked than cold-rolled (cold-reduced)

Consigned from Taiwan, Türkiye or Viet Nam

Of a thickness of 3 mm or more but less than 4,75 mm

Consigned from Taiwan, Türkiye or Viet Nam

Containing by weight less than 2,5 % of nickel

Other

Containing by weight 2,5 % or more of nickel

Other

Consigned from Taiwan, Türkiye or Viet Nam

Of a thickness of 0,5 mm or more but not exceeding 1 mm

Consigned from Taiwan, Türkiye or Viet Nam

Containing by weight less than 2,5 % of nickel

Other

Containing by weight 2,5 % or more of nickel

Other

Consigned from Taiwan, Türkiye or Viet Nam

Other

Consigned from Taiwan, Türkiye or Viet Nam

Other

Other

Not further worked than hot-rolled

Consigned from Türkiye

Of a thickness of less than 4,75 mm

Other

Of a thickness of 3 mm or more, containing by weight

Consigned from Taiwan, Türkiye or Viet Nam

Less than 2,5 % of nickel

Other

2,5 % or more of nickel

Other

Consigned from Taiwan, Türkiye or Viet Nam

Of a thickness not exceeding 0,35 mm, containing by weight

Consigned from Taiwan, Türkiye or Viet Nam

Less than 2,5 % of nickel

Other

Perforated

Other

Consigned from Taiwan, Türkiye or Viet Nam

Bars and rods, hot-rolled, in irregularly wound coils, of stainless steel

Containing by weight less than 2,5 % of nickel

Bars and rods, not further worked than hot-rolled, hot-drawn or extruded

Of a diameter of 80 mm or more, containing by weight

Less than 2,5 % of nickel

2,5 % or more of nickel

Other

Containing by weight less than 2,5 % of nickel

Of circular cross-section

2,5 % or more of nickel

Of a diameter of 25 mm or more, but less than 80 mm, containing by weight

Less than 2,5 % of nickel

2,5 % or more of nickel

Other, containing by weight

Less than 2,5 % of nickel

Forged, containing by weight

Less than 2,5 % of nickel

Hot-rolled, hot-drawn or extruded, not further worked than clad

Angles, shapes and sections

Not further worked than cold-formed or cold-finished

Hot-rolled, hot-drawn or extruded, not further worked than clad

Wire of stainless steel

Containing by weight 28 % or more but not more than 31 % of nickel and 20 % or more but not more than 22 % of chromium

Containing by weight less than 2,5 % of nickel

Other

Other alloy steel in ingots or other primary forms; semi-finished products of other alloy steel

Of tool steel

Other

Of rectangular (including square) cross-section

Hot-rolled or obtained by continuous casting

Other

Hot-rolled or obtained by continuous casting

Of high-speed steel

Other

Forged

Hot-rolled or obtained by continuous casting

Other

Flat-rolled products of other alloy steel, of a width of 600 mm or more

Grain-oriented

With a maximum core loss not higher than 0.9 W/kg

With a maximum core loss higher than 1,05 W/kg

Other

Products clad, plated or coated, not in coils, without patterns in relief, of a thickness exceeding 10 mm and products clad, plated or coated, not in coils, without patterns in relief, of a thickness of 4,75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more

Cold-rolled

Of tool steel

Not further worked than rolled; not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square)

Other

Of tool steel

Other

Of a thickness of 4,75 mm or more but not exceeding 10 mm

Other

Other, not further worked than cold-rolled (cold-reduced)

Not further worked than rolled; not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square)

Other

Electrolytically plated or coated with zinc

Other

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square)

Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with additional surface treatment such as oiling or sealing; containing by weight: not more than 0,5% of carbon, not more than 1,1% of aluminium, not more than 0,12% of niobium, not more than 0,17% of titanium and not more than 0,15% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Of silicon-electrical steel

Of a width exceeding 500 mm

With a maximum core loss not higher than 0.9 W/kg

With a maximum core loss higher than 1,05 W/kg

Of a width not exceeding 500 mm

With a maximum core loss not higher than 0.9 W/kg

With a maximum core loss higher than 1,05 W/kg

Other

Products clad, plated or coated

Of a width not exceeding 350 mm and of a thickness of 50 mm or more

Other

Of a width not exceeding 500 mm

Products further worked than hot rolled, or clad, plated or coated

Other

Of tool steel

Of a thickness of 4,75 mm or more

Other

Not further worked than cold-rolled (cold-reduced)

Of a width not exceeding 500 mm

Electrolytically plated or coated with zinc

Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Of a width not exceeding 500 mm, hot-rolled, not further worked than clad; of a width exceeding 500 mm, not further worked than surface-treated, including cladding

Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with or without additional surface treatment such as oiling or sealing; containing by weight: not more than 0,5% of carbon, not more than 1,1% of aluminium, not more than 0,12% of niobium, not more than 0,17% of titanium and not more than 0,15% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with or without additional surface treatment such as oiling or sealing; containing by weight: not more than 0,5% of carbon, not more than 1,1% of aluminium, not more than 0,12% of niobium, not more than 0,17% of titanium and not more than 0,15% of vanadium; presented in coils, cut-to-length sheets and narrow strips

Other

Of high-speed steel

Other

Containing by weight 0,9 % or more but not more than 1,15 % of carbon, 0,5 % or more but not more than 2 % of chromium and, if present, not more than 0,5 % of molybdenum

Other bars and rods of other alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or non-alloy steel

Not further worked than hot-rolled, hot-drawn or extruded; hot-rolled, hot-drawn or extruded, not further worked than clad

Other

Of rectangular (other than square) cross-section, hot-rolled on four faces

Other

Other

Not further worked than hot-rolled, hot-drawn or extruded; hot-rolled, hot-drawn or extruded, not further worked than clad

Other bars and rods, not further worked than hot-rolled, hot-drawn or extruded

High fatigue performance concrete reinforcing bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling

Containing by weight 0,9 % or more but not more than 1,15 % of carbon, 0,5 % or more but not more than 2 % of chromium and, if present, not more than 0,5 % of molybdenum

High fatigue performance concrete reinforcing bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling

Other

Other

Of circular cross-section, of a diameter of

High fatigue performance concrete reinforcing bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling

Less than 80 mm

Other

High fatigue performance concrete reinforcing bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling

Other

Other

Of tool steel

Other bars and rods, not further worked than cold-formed or cold-finished

Containing by weight 0,9 % or more but not more than 1,15 % of carbon, 0,5 % or more but not more than 2 % of chromium and, if present, not more than 0,5 % of molybdenum

Of circular cross-section, of a diameter of

Less than 80 mm

Other bars and rods

Hot-rolled, hot-drawn or extruded, not further worked than clad

Other

Other

Not further worked than hot-rolled, hot-drawn or extruded

Hot-rolled, hot-drawn or extruded, not further worked than clad

Hollow drill bars and rods

Of silico-manganese steel

Of high-speed steel

Other