Browse HS Codes - 72: IRON AND STEEL
| 7201 | Pig iron and spiegeleisen in pigs, blocks or other primary forms |
| 7201.A | Non-alloy pig iron containing by weight 0.5% or less of phosphorus |
| 7201.A.A | Containing by weight not less than 0.4% of manganese |
| 7201.A.A.A | Containing by weight 1% or less of silicon |
| - | Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm |
| - | Other |
| - | Containing by weight more than 1% of silicon |
| 7201.A.B | Containing by weight not less than 0.1% but less than 0.4% of manganese |
| - | Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm, containing by weight not more than 1% of silicon |
| - | Other |
| - | Containing by weight less than 0.1% of manganese |
| - | Non-alloy pig iron containing by weight more than 0.5% of phosphorus |
| 7201.B | Alloy pig iron; spiegeleisen |
| - | Alloy pig iron containing by weight not less than 0.3% but not more than 1% of titanium and not less than 0.5% but not more than 1% of vanadium |
| - | Other |
| 7201 | Pig iron and spiegeleisen in pigs, blocks or other primary forms |
| 7201.C | Non-alloy pig iron containing by weight 0.5% or less of phosphorus |
| 7201.C.A | Containing by weight not less than 0.4% of manganese |
| 7201.C.A.A | Containing by weight 1% or less of silicon |
| - | Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm |
| - | Other |
| - | Containing by weight more than 1% of silicon |
| 7201.C.B | Containing by weight not less than 0.1% but less than 0.4% of manganese |
| - | Pig iron ingots with a length of not more than 350 mm, a width of not more than 150 mm, a height of not more than 150 mm, containing by weight not more than 1% of silicon |
| - | Other |
| - | Containing by weight less than 0.1% of manganese |
| - | Non-alloy pig iron containing by weight more than 0.5% of phosphorus |
| 7201.D | Alloy pig iron; spiegeleisen |
| - | Alloy pig iron containing by weight not less than 0.3% but not more than 1% of titanium and not less than 0.5% but not more than 1% of vanadium |
| - | Other |
| 7202 | Ferro-alloys |
| 7202.A | Ferro-manganese |
| 7202.A.A | Containing by weight more than 2% of carbon |
| - | With a granulometry not exceeding 5 mm and a manganese content by weight exceeding 65% |
| - | Other |
| - | Other |
| 7202.B | Ferro-silicon |
| - | Containing by weight more than 55% of silicon |
| 7202.B.A | Other |
| - | Containing by weight 4% or more but not more than 10% of magnesium |
| - | Other |
| - | Ferro-silico-manganese |
| 7202.C | Ferro-chromium |
| 7202.C.A | Containing by weight more than 4% of carbon |
| - | Containing by weight more than 4% but not more than 6% of carbon |
| - | Containing by weight more than 6% of carbon |
| 7202.C.B | Other |
| 7202.C.B.A | Containing by weight not more than 0.05% of carbon |
| - | Containing by weight more than 30% but not more than 90% of chromium (super-refined ferrochromium) |
| - | Other |
| 7202.C.B.B | Containing by weight more than 0.05% but not more than 0.5% of carbon |
| 7202.C.B.B.A | With a chromium content by weight of 30% and more |
| - | Containing by weight not more than 0.1% of carbon and more than 30% but not more than 90% of chromium (super-refined ferrochromium) |
| - | Other |
| - | Other |
| - | Containing by weight more than 0.5% but not more than 4% of carbon |
| - | Ferro-silico-chromium |
| - | Ferro-nickel |
| - | Ferro-molybdenum |
| - | Ferro-tungsten and ferro-silico-tungsten |
| 7202.D | Other |
| - | Ferro-titanium and ferro-silico-titanium |
| - | Ferro-vanadium |
| - | Ferro-niobium |
| 7202.D.A | Other |
| - | Ferro-phosphorus |
| - | Ferro-silico-magnesium |
| 7202.D.A.A | Other |
| - | Ferro-dysprosium, containing by weight:- 78% or more of dysprosium and- 18% or more but no more than 22% of iron |
| - | Calcium-silicon - an alloy that contains by weight 16% or more of calcium, 45% or more of silicon, not less than 4% but less than 14% of iron and not more than 10% of any other element; whether or not presented in bulk, packaged in bags or in steel drums, enclosed in steel sheets (or cored wire), or otherwise presented |
| - | Other |
| 7203 | Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99.94%, in lumps, pellets or similar forms |
| - | Ferrous products obtained by direct reduction of iron ore |
| - | Other |
| 7204 | Ferrous waste and scrap; remelting scrap ingots of iron or steel |
| - | Waste and scrap of cast iron |
| 7204.A | Waste and scrap of alloy steel |
| 7204.A.A | Of stainless steel |
| 7204.A.A.A | Containing by weight 8% or more of nickel |
| - | Scrap |
| - | Other |
| 7204.A.A.B | Other |
| - | Scrap |
| - | Other |
| 7204.A.B | Other |
| - | Scrap |
| - | Other |
| 7204.B | Waste and scrap of tinned iron or steel |
| - | Scrap |
| - | Other |
| 7204.C | Other waste and scrap |
| 7204.C.A | Turnings, shavings, chips, milling waste, sawdust, filings, trimmings and stampings, whether or not in bundles |
| 7204.C.A.A | Turnings, shavings, chips, milling waste, sawdust and filings |
| - | Scrap |
| - | Other |
| 7204.C.A.B | Trimmings and stampings |
| 7204.C.A.B.A | In bundles |
| - | Scrap |
| - | Other |
| 7204.C.A.B.B | Other |
| - | Scrap |
| - | Other |
| 7204.C.B | Other |
| 7204.C.B.A | Fragmentised (shredded) |
| - | Scrap |
| - | Other |
| 7204.C.B.B | Other |
| 7204.C.B.B.A | In bundles |
| - | Scrap |
| - | Other |
| 7204.C.B.B.B | Other |
| - | Scrap |
| - | Other |
| - | Remelting scrap ingots |
| 7205 | Granules and powders, of pig iron, spiegeleisen, iron or steel |
| - | Granules |
| 7205.A | Powders |
| - | Of alloy steel |
| - | Other |
| 7206 | Iron and non-alloy steel in ingots or other primary forms (excluding iron of heading 7203) |
| - | Ingots |
| - | Other |
| 7206 | Iron and non-alloy steel in ingots or other primary forms (excluding iron of heading 7203) |
| - | Ingots |
| - | Other |
| 7207 | Semi-finished products of iron or non-alloy steel |
| 7207.A | Containing by weight less than 0.25% of carbon |
| 7207.A.A | Of rectangular (including square) cross-section, the width measuring less than twice the thickness |
| 7207.A.A.A | Rolled or obtained by continuous casting |
| - | Of free-cutting steel |
| 7207.A.A.A.A | Other |
| - | Of a thickness not exceeding 130 mm |
| - | Of a thickness exceeding 130 mm |
| - | Forged |
| 7207.A.B | Other, of rectangular (other than square) cross-section |
| - | Rolled or obtained by continuous casting |
| - | Forged |
| 7207.A.C | Other |
| 7207.A.C.A | Of circular or polygonal cross-section |
| - | Rolled or obtained by continuous casting |
| - | Forged |
| 7207.A.C.B | Other |
| - | Blanks for angles, shapes and sections, rolled or obtained by continuous casting |
| - | Other |
| 7207.B | Containing by weight 0.25% or more of carbon |
| 7207.B.A | Of rectangular (including square) cross-section, the width measuring less than twice the thickness |
| 7207.B.A.A | Rolled or obtained by continuous casting |
| - | Of free-cutting steel |
| 7207.B.A.A.A | Other, containing by weight |
| - | 0.25% or more but less than 0.6% of carbon |
| - | 0.6% or more of carbon |
| - | Forged |
| 7207.B.B | Other, of rectangular (other than square) cross-section |
| - | Rolled or obtained by continuous casting |
| - | Forged |
| 7207.B.C | Of circular or polygonal cross-section |
| - | Rolled or obtained by continuous casting |
| - | Forged |
| 7207.B.D | Other |
| - | Blanks for angles, shapes and sections, rolled or obtained by continuous casting |
| - | Other |
| 7208 | Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, hot-rolled, not clad, plated or coated |
| - | In coils, not further worked than hot-rolled, with patterns in relief |
| 7208.A | Other, in coils, not further worked than hot-rolled, pickled |
| - | Of a thickness of 4.75 mm or more |
| - | Of a thickness of 3 mm or more but less than 4.75 mm |
| - | Of a thickness of less than 3 mm |
| 7208.B | Other, in coils, not further worked than hot-rolled |
| - | Of a thickness exceeding 10 mm |
| 7208.B.A | Of a thickness of 4.75 mm or more but not exceeding 10 mm |
| - | Intended for re-rolling |
| - | Other |
| 7208.B.B | Of a thickness of 3 mm or more but less than 4.75 mm |
| - | Intended for re-rolling |
| - | Other |
| 7208.B.C | Of a thickness of less than 3 mm |
| - | Intended for re-rolling |
| - | Other |
| 7208.C | Not in coils, not further worked than hot-rolled, with patterns in relief |
| - | Of a thickness of 2 mm or more |
| - | Of a thickness of less than 2 mm |
| 7208.D | Other, not in coils, not further worked than hot-rolled |
| 7208.D.A | Of a thickness exceeding 10 mm |
| 7208.D.A.A | Of a thickness exceeding 15 mm |
| - | Of non-alloy steel, excluding tool steel |
| - | Other |
| 7208.D.A.B | Of a thickness exceeding 10 mm but not exceeding 15 mm, of a width of |
| 7208.D.A.B.A | 2 050 mm or more |
| - | Of non-alloy steel, excluding tool steel |
| - | Other |
| 7208.D.A.B.B | Less than 2 050 mm |
| - | Of non-alloy steel, excluding tool steel |
| - | Other |
| 7208.D.B | Of a thickness of 4.75 mm or more but not exceeding 10 mm |
| - | Rolled on four faces or in a closed box pass, of a width not exceeding 1 250 mm |
| 7208.D.B.A | Other, of a width of |
| 7208.D.B.A.A | 2 050 mm or more |
| - | Of non-alloy steel, excluding tool steel |
| - | Other |
| - | Less than 2 050 mm |
| 7208.D.C | Of a thickness of 3 mm or more but less than 4.75 mm |
| - | Rolled on four faces or in a closed box pass, of a width not exceeding 1 250 mm and of a thickness of 4 mm or more |
| - | Other |
| - | Of a thickness of less than 3 mm |
| 7208.E | Other |
| 7208.E.A | Perforated |
| - | Of non-alloy steel, excluding tool steel, of a thickness exceeding 10 mm or of a thickness of 4.75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more |
| - | Other |
| 7208.E.B | Other |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Of non-alloy steel, excluding tool steel, of a thickness exceeding 10 mm or of a thickness of 4.75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more |
| - | Other |
| 7209 | Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated |
| 7209.A | In coils, not further worked than cold-rolled (cold-reduced) |
| 7209.A.A | Of a thickness of 3 mm or more |
| - | 'electrical' |
| - | Other |
| 7209.A.B | Of a thickness exceeding 1 mm but less than 3 mm |
| - | 'electrical' |
| - | Other |
| 7209.A.C | Of a thickness of 0.5 mm or more but not exceeding 1 mm |
| - | 'electrical' |
| - | Other |
| 7209.A.D | Of a thickness of less than 0.5 mm |
| - | 'electrical' |
| 7209.A.D.A | Other |
| - | Of a thickness of 0.35 mm or more but less than 0.5 mm |
| 7209.A.D.A.A | Of a thickness of less than 0.35 mm |
| - | Annealed (known as 'black plates') |
| - | Other |
| 7209.B | Not in coils, not further worked than cold-rolled (cold-reduced) |
| 7209.B.A | Of a thickness of 3 mm or more |
| - | 'electrical' |
| - | Other |
| 7209.B.B | Of a thickness exceeding 1 mm but less than 3 mm |
| - | 'electrical' |
| - | Other |
| 7209.B.C | Of a thickness of 0.5 mm or more but not exceeding 1 mm |
| - | 'electrical' |
| - | Other |
| 7209.B.D | Of a thickness of less than 0.5 mm |
| - | 'electrical' |
| - | Other |
| 7209.C | Other |
| - | Perforated |
| 7209.C.A | Other |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210 | Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated |
| 7210.A | Plated or coated with tin |
| 7210.A.A | Of a thickness of 0.5 mm or more |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210.A.B | Of a thickness of less than 0.5 mm |
| 7210.A.B.A | Tinplate |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210.A.B.B | Other |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210.B | Plated or coated with lead, including terne-plate |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210.C | Electrolytically plated or coated with zinc |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210.D | Otherwise plated or coated with zinc |
| 7210.D.A | Corrugated |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7210.D.B | Other |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7210.E | Plated or coated with chromium oxides or with chromium and chromium oxides |
| - | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210.F | Plated or coated with aluminium |
| 7210.F.A | Plated or coated with aluminium-zinc alloys |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7210.F.B | Other |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation with aluminium and/or magnesium, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7210.G | Painted, varnished or coated with plastics |
| 7210.G.A | Tinplate, varnished; products, plated or coated with chromium oxides or with chromium and chromium oxides, varnished |
| - | Tinplate |
| - | Other |
| 7210.G.B | Other |
| 7210.G.B.A | Not further worked than surface-treated or simply cut into shapes other than rectangular (including square) |
| - | Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| 7210.G.B.A.A | Other |
| - | Coated or plated with tin |
| - | Other |
| 7210.G.B.B | Other |
| - | Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding so-called 'sandwich panels' of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, and excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| 7210.G.B.B.A | Other |
| - | Coated or plated with tin |
| - | Other |
| 7210.H | Other |
| - | Clad |
| 7210.H.A | Tinned and printed |
| - | Not further worked than surface-treated, including cladding, or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7210.H.B | Other |
| - | Coated or plated with tin, whether or not coated with a plastic material and/or varnished |
| 7210.H.B.A | Other |
| - | Not further worked than surface-treated, including cladding, or simply cut into shapes other than rectangular (including square) |
| - | Plated or coated by hot dip galvanisation with magnesium or magnesium-zinc alloys, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7211 | Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, not clad, plated or coated |
| 7211.A | Not further worked than hot-rolled |
| 7211.A.A | Rolled on four faces or in a closed box pass, of a width exceeding 150 mm and a thickness of not less than 4 mm, not in coils and without patterns in relief |
| - | Of a width not exceeding 350 mm and of a thickness of 50 mm or more |
| - | Other |
| 7211.A.B | Other, of a thickness of 4.75 mm or more |
| - | Of a width exceeding 500 mm |
| 7211.A.B.A | Of a width not exceeding 500 mm |
| - | Of a width not exceeding 350 mm and of a thickness of 50 mm or more |
| - | Other |
| 7211.A.C | Other |
| - | Of a width exceeding 500 mm |
| 7211.A.C.A | Of a width not exceeding 500 mm |
| - | Of a width not exceeding 350 mm and of a thickness of 50 mm or more |
| - | Other |
| 7211.B | Not further worked than cold-rolled (cold-reduced) |
| 7211.B.A | Containing by weight less than 0.25% of carbon |
| 7211.B.A.A | 'electrical' |
| - | Of a width exceeding 500 mm |
| - | Of a width not exceeding 500 mm |
| 7211.B.A.B | Other |
| 7211.B.A.B.A | Of a thickness of 0.35 mm or more |
| - | Of a width exceeding 500 mm |
| 7211.B.A.B.A.A | Of a width not exceeding 500 mm |
| - | In coils intended for the manufacture of tinplate |
| - | Other |
| 7211.B.A.B.B | Of a thickness of less than 0.35 mm |
| 7211.B.A.B.B.A | Of a width exceeding 500 mm |
| - | In coils, annealed (known as 'black plates') |
| - | Other |
| 7211.B.A.B.B.B | Of a width not exceeding 500 mm |
| 7211.B.A.B.B.B.A | In coils intended for the manufacture of tinplate |
| - | Annealed (known as 'black plates') |
| - | Other |
| 7211.B.A.B.B.B.B | Other |
| - | In coils, annealed (known as 'black plates') |
| - | Other |
| 7211.B.B | Other |
| 7211.B.B.A | Of a width exceeding 500 mm |
| - | 'electrical' |
| - | Other |
| 7211.B.B.B | Of a width not exceeding 500 mm |
| - | 'electrical' |
| - | Other |
| 7211.C | Other |
| - | Perforated |
| 7211.C.A | Other |
| 7211.C.A.A | Of a width exceeding 500 mm |
| - | Not further worked than surface-treated |
| - | Other |
| - | Of a width not exceeding 500 mm |
| 7212 | Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, clad, plated or coated |
| 7212.A | Plated or coated with tin |
| - | Tinplate, not further worked than surface-treated |
| 7212.A.A | Other |
| 7212.A.A.A | Of a width exceeding 500 mm |
| - | Not further worked than surface-treated |
| - | Other |
| - | Of a width not exceeding 500 mm |
| 7212.B | Electrolytically plated or coated with zinc |
| 7212.B.A | Of a width exceeding 500 mm |
| - | Not further worked than surface-treated |
| - | Other |
| - | Of a width not exceeding 500 mm |
| 7212.C | Otherwise plated or coated with zinc |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7212.D | Painted, varnished or coated with plastics |
| 7212.D.A | Tinplate, not further worked than varnished; products, plated or coated with chromium oxides or with chromium and chromium oxides, varnished |
| - | Tinplate, not further worked than varnished |
| 7212.D.A.A | Other |
| 7212.D.A.A.A | Of a width exceeding 500 mm |
| - | Not further worked than surface-treated |
| - | Other |
| - | Of a width not exceeding 500 mm |
| 7212.D.B | Other |
| 7212.D.B.A | Of a width exceeding 500 mm |
| 7212.D.B.A.A | Not further worked than surface-treated |
| - | Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| 7212.D.B.A.A.A | Other |
| - | Coated or plated with tin |
| - | Other |
| 7212.D.B.A.B | Other |
| - | Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding so-called 'sandwich panels' of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, and excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| 7212.D.B.A.B.A | Other |
| - | Coated or plated with tin |
| - | Other |
| 7212.D.B.B | Of a width not exceeding 500 mm |
| 7212.D.B.B.A | Of non-alloy steel, painted, varnished or coated with plastics on at least one side, excluding so-called 'sandwich panels' of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, and excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) |
| - | Coated or plated with tin |
| - | Other |
| 7212.D.B.B.B | Other |
| - | Coated or plated with tin |
| - | Other |
| 7212.E | Otherwise plated or coated |
| 7212.E.A | Plated or coated with chromium oxides or with chromium and chromium oxides |
| 7212.E.A.A | Of a width exceeding 500 mm |
| - | Not further worked than surface-treated |
| - | Other |
| - | Of a width not exceeding 500 mm |
| 7212.E.B | Plated or coated with chromium or nickel |
| 7212.E.B.A | Of a width exceeding 500 mm |
| - | Not further worked than surface-treated |
| - | Other |
| - | Of a width not exceeding 500 mm |
| 7212.E.C | Plated or coated with copper |
| 7212.E.C.A | Of a width exceeding 500 mm |
| - | Not further worked than surface-treated |
| - | Other |
| - | Of a width not exceeding 500 mm |
| 7212.E.D | Plated or coated with aluminium |
| 7212.E.D.A | Plated or coated with aluminium-zinc alloys |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7212.E.D.B | Other |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7212.E.E | Other |
| 7212.E.E.A | Of a width exceeding 500 mm |
| - | Silvered, gilded, platinum-plated or enamelled |
| 7212.E.E.A.A | Other |
| - | Not further worked than surface-treated |
| - | Plated or coated by hot dip galvanisation with magnesium or magnesium-zinc alloys, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7212.E.E.B | Of a width not exceeding 500 mm |
| - | Plated or coated by hot dip galvanisation with magnesium or magnesium-zinc alloys, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| - | Clad |
| 7213 | Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel |
| - | Containing indentations, ribs, grooves or other deformations produced during the rolling process |
| - | Other, of free-cutting steel |
| 7213.A | Other |
| 7213.A.A | Of circular cross-section measuring less than 14 mm in diameter |
| - | Of a type used for concrete reinforcement |
| - | Of a type used for tyre cord |
| 7213.A.A.A | Other |
| - | Containing by weight 0.06% or less of carbon |
| - | Containing by weight more than 0.06% but less than 0.25% of carbon |
| - | Containing by weight 0.25% or more but not more than 0.75% of carbon |
| - | Containing by weight more than 0.75% of carbon |
| 7213.A.B | Other |
| - | Containing by weight less than 0.25% of carbon |
| - | Containing by weight 0.25% or more of carbon |
| 7214 | Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling |
| 7214.A | Forged |
| - | Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars |
| - | Other |
| 7214.B | Containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling |
| - | High fatigue performance concrete reinforcing bars and rods |
| 7214.B.A | Other |
| - | Concrete reinforcement bars and rods excluding long products, such as round bars |
| - | Other |
| 7214.C | Other, of free-cutting steel |
| - | Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars |
| - | Other |
| 7214.D | Other |
| 7214.D.A | Of rectangular (other than square) cross-section |
| 7214.D.A.A | Containing by weight less than 0.25% of carbon |
| - | Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars |
| - | Other |
| 7214.D.A.B | Containing by weight 0.25% or more of carbon |
| - | Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars |
| - | Other |
| 7214.D.B | Other |
| 7214.D.B.A | Containing by weight less than 0.25% of carbon |
| 7214.D.B.A.A | Of a type used for concrete reinforcement |
| - | Bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance bars and rods, and excluding other long products, such as round bars |
| - | Other |
| 7214.D.B.A.B | Other, of circular cross-section measuring in diameter |
| - | 80 mm or more |
| - | Less than 80 mm |
| - | Other |
| 7214.D.B.B | Containing by weight 0.25% or more of carbon |
| 7214.D.B.B.A | Of a circular cross-section measuring in diameter |
| - | 80 mm or more |
| - | Less than 80 mm |
| 7214.D.B.B.B | Other |
| - | Concrete reinforcement bars and rods, containing indentations, ribs, grooves or other deformations produced during the rolling process; excluding high fatigue performance concrete reinforcement bars and rods, and excluding other long products, such as round bars |
| - | Other |
| 7215 | Other bars and rods of iron or non-alloy steel |
| - | Of free-cutting steel, not further worked than cold-formed or cold-finished |
| 7215.A | Other, not further worked than cold-formed or cold-finished |
| 7215.A.A | Containing by weight less than 0.25% of carbon |
| - | Of rectangular (other than square) cross-section |
| - | Other |
| - | Containing by weight 0.25% or more of carbon |
| 7215.B | Other |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7216 | Angles, shapes and sections of iron or non-alloy steel |
| - | U, i or h sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm |
| 7216.A | L or t sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm |
| - | L sections |
| - | T sections |
| 7216.B | U, i or h sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more |
| 7216.B.A | U sections |
| - | Of a height of 80 mm or more but not exceeding 220 mm |
| - | Of a height exceeding 220 mm |
| 7216.B.B | I sections |
| 7216.B.B.A | Of a height of 80 mm or more but not exceeding 220 mm |
| - | With parallel flange faces |
| - | Other |
| 7216.B.B.B | Of a height exceeding 220 mm |
| - | With parallel flange faces |
| - | Other |
| 7216.B.C | H sections |
| - | Of a height of 80 mm or more but not exceeding 180 mm |
| - | Of a height exceeding 180 mm |
| 7216.C | L or t sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more |
| - | L sections |
| - | T sections |
| 7216.D | Other angles, shapes and sections, not further worked than hot-rolled, hot-drawn or extruded |
| - | With a cross-section which is capable of being enclosed in a square the side of which is 80 mm |
| 7216.D.A | Other |
| 7216.D.A.A | Bulb flats |
| - | In the range up to 204 mm width |
| - | Other |
| - | Other |
| 7216.E | Angles, shapes and sections, not further worked than cold-formed or cold-finished |
| 7216.E.A | Obtained from flat-rolled products |
| - | C, l, u, z, omega or open-ended sections |
| - | Other |
| - | Other |
| 7216.F | Other |
| 7216.F.A | Cold-formed or cold-finished from flat-rolled products |
| - | Profiled (ribbed) sheets |
| - | Other |
| 7216.F.B | Other |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7217 | Wire of iron or non-alloy steel |
| 7217.A | Not plated or coated, whether or not polished |
| 7217.A.A | Containing by weight less than 0.25% of carbon |
| - | With a maximum cross-sectional dimension of less than 0.8 mm |
| 7217.A.A.A | With a maximum cross-sectional dimension of 0.8 mm or more |
| - | Containing indentations, ribs, grooves or other deformations produced during the rolling process |
| - | Other |
| - | Containing by weight 0.25% or more but less than 0.6% of carbon |
| 7217.A.B | Containing by weight 0.6% or more of carbon |
| - | Of non-alloy steel, with a maximum cross-sectional dimension exceeding 3 mm |
| - | Other |
| 7217.B | Plated or coated with zinc |
| 7217.B.A | Containing by weight less than 0.25% of carbon |
| - | With a maximum cross-sectional dimension of less than 0.8 mm |
| - | With a maximum cross-sectional dimension of 0.8 mm or more |
| - | Containing by weight 0.25% or more but less than 0.6% of carbon |
| 7217.B.B | Containing by weight 0.6% or more of carbon |
| - | Of non-alloy steel, with a maximum cross-sectional dimension exceeding 3 mm |
| - | Other |
| 7217.C | Plated or coated with other base metals |
| 7217.C.A | Containing by weight less than 0.25% of carbon |
| - | Copper-coated |
| - | Other |
| - | Containing by weight 0.25% or more but less than 0.6% of carbon |
| - | Containing by weight 0.6% or more of carbon |
| 7217.D | Other |
| - | Containing by weight less than 0.25% of carbon |
| - | Containing by weight 0.25% or more but less than 0.6% of carbon |
| - | Containing by weight 0.6% or more of carbon |
| 7218 | Stainless steel in ingots or other primary forms; semi-finished products of stainless steel |
| - | Ingots and other primary forms |
| 7218.A | Other |
| 7218.A.A | Of rectangular (other than square) cross-section |
| - | Containing by weight 2.5% or more of nickel |
| - | Containing by weight less than 2.5% of nickel |
| 7218.A.B | Other |
| 7218.A.B.A | Of square cross-section |
| - | Rolled or obtained by continous casting |
| - | Forged |
| 7218.A.B.B | Other |
| - | Rolled or obtained by continuous casting |
| - | Forged |
| 7218 | Stainless steel in ingots or other primary forms; semi-finished products of stainless steel |
| - | Ingots and other primary forms |
| 7218.B | Other |
| 7218.B.A | Of rectangular (other than square) cross-section |
| - | Containing by weight 2.5% or more of nickel |
| - | Containing by weight less than 2.5% of nickel |
| 7218.B.B | Other |
| 7218.B.B.A | Of square cross-section |
| - | Rolled or obtained by continous casting |
| - | Forged |
| 7218.B.B.B | Other |
| - | Rolled or obtained by continuous casting |
| - | Forged |
| 7219 | Flat-rolled products of stainless steel, of a width of 600 mm or more |
| 7219.A | Not further worked than hot-rolled, in coils |
| 7219.A.A | Of a thickness exceeding 10 mm |
| - | Consigned from Türkiye |
| - | Other |
| 7219.A.B | Of a thickness of 4.75 mm or more but not exceeding 10 mm |
| 7219.A.B.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.A.B.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.A.C | Of a thickness of 3 mm or more but less than 4.75 mm |
| 7219.A.C.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.A.C.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.A.D | Of a thickness of less than 3 mm |
| 7219.A.D.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.A.D.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.B | Not further worked than hot-rolled, not in coils |
| 7219.B.A | Of a thickness exceeding 10 mm |
| - | Containing by weight 2.5% or more of nickel |
| - | Containing by weight less than 2.5% of nickel |
| 7219.B.B | Of a thickness of 4.75 mm or more but not exceeding 10 mm |
| 7219.B.B.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.B.B.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Türkiye |
| - | Other |
| 7219.B.C | Of a thickness of 3 mm or more but less than 4.75 mm |
| - | Consigned from Türkiye |
| - | Other |
| 7219.B.D | Of a thickness of less than 3 mm |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C | Not further worked than cold-rolled (cold-reduced) |
| 7219.C.A | Of a thickness of 4.75 mm or more |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.B | Of a thickness of 3 mm or more but less than 4.75 mm |
| 7219.C.B.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.B.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.C | Of a thickness exceeding 1 mm but less than 3 mm |
| 7219.C.C.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.C.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.D | Of a thickness of 0.5 mm or more but not exceeding 1 mm |
| 7219.C.D.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.D.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.E | Of a thickness of less than 0.5 mm |
| 7219.C.E.A | Containing by weight 2.5% or more of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.C.E.B | Containing by weight less than 2.5% of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.D | Other |
| 7219.D.A | Perforated |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7219.D.B | Other |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220 | Flat-rolled products of stainless steel, of a width of less than 600 mm |
| 7220.A | Not further worked than hot-rolled |
| 7220.A.A | Of a thickness of 4.75 mm or more |
| - | Consigned from Türkiye |
| - | Other |
| 7220.A.B | Of a thickness of less than 4.75 mm |
| - | Consigned from Türkiye |
| - | Other |
| 7220.B | Not further worked than cold-rolled (cold-reduced) |
| 7220.B.A | Of a thickness of 3 mm or more, containing by weight |
| 7220.B.A.A | 2.5% or more of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220.B.A.B | Less than 2.5% of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220.B.B | Of a thickness exceeding 0.35 mm but of less than 3 mm, containing by weight |
| 7220.B.B.A | 2.5% or more of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220.B.B.B | Less than 2.5% of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220.B.C | Of a thickness not exceeding 0.35 mm, containing by weight |
| 7220.B.C.A | 2.5% or more of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220.B.C.B | Less than 2.5% of nickel |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220.C | Other |
| 7220.C.A | Perforated |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7220.C.B | Other |
| - | Consigned from Taiwan or Vietnam |
| - | Consigned from Türkiye |
| - | Other |
| 7221 | Bars and rods, hot-rolled, in irregularly wound coils, of stainless steel |
| - | Containing by weight 2.5% or more of nickel |
| - | Containing by weight less than 2.5% of nickel |
| 7222 | Other bars and rods of stainless steel; angles, shapes and sections of stainless steel |
| 7222.A | Bars and rods, not further worked than hot-rolled, hot-drawn or extruded |
| 7222.A.A | Of circular cross-section |
| 7222.A.A.A | Of a diameter of 80 mm or more, containing by weight |
| - | 2.5% or more of nickel |
| - | Less than 2.5% of nickel |
| 7222.A.A.B | Of a diameter of less than 80 mm, containing by weight |
| - | 2.5% or more of nickel |
| - | Less than 2.5% of nickel |
| 7222.A.B | Other |
| - | Containing by weight 2.5% or more of nickel |
| - | Containing by weight less than 2.5% of nickel |
| 7222.B | Bars and rods, not further worked than cold-formed or cold-finished |
| 7222.B.A | Of circular cross-section |
| 7222.B.A.A | Of a diameter of 80 mm or more, containing by weight |
| - | 2.5% or more of nickel |
| - | Less than 2.5% of nickel |
| 7222.B.A.B | Of a diameter of 25 mm or more, but less than 80 mm, containing by weight |
| - | 2.5% or more of nickel |
| - | Less than 2.5% of nickel |
| 7222.B.A.C | Of a diameter of less than 25 mm, containing by weight |
| - | 2.5% or more of nickel |
| - | Less than 2.5% of nickel |
| 7222.B.B | Other, containing by weight |
| - | 2.5% or more of nickel |
| - | Less than 2.5% of nickel |
| 7222.C | Other bars and rods |
| 7222.C.A | Forged, containing by weight |
| - | 2.5% or more of nickel |
| - | Less than 2.5% of nickel |
| 7222.C.B | Other |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7222.D | Angles, shapes and sections |
| - | Not further worked than hot-rolled, hot-drawn or extruded |
| - | Not further worked than cold-formed or cold-finished |
| 7222.D.A | Other |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7223 | Wire of stainless steel |
| 7223.A | Containing by weight 2.5% or more of nickel |
| - | Containing by weight 28% or more but not more than 31% of nickel and 20% or more but not more than 22% of chromium |
| - | Other |
| 7223.B | Containing by weight less than 2.5% of nickel |
| - | Containing by weight 13% or more but not more than 25% of chromium and 3.5% or more but not more than 6% of aluminium |
| - | Other |
| 7224 | Other alloy steel in ingots or other primary forms; semi-finished products of other alloy steel |
| 7224.A | Ingots and other primary forms |
| - | Of tool steel |
| - | Other |
| 7224.B | Other |
| 7224.B.A | Of tool steel |
| - | Of rectangular (including square) cross-section |
| 7224.B.A.A | Other |
| - | Hot-rolled or obtained by continuous casting |
| - | Other |
| 7224.B.B | Other |
| 7224.B.B.A | Of rectangular (including square) cross-section |
| 7224.B.B.A.A | Hot-rolled or obtained by continuous casting |
| 7224.B.B.A.A.A | The width measuring less than twice the thickness |
| - | Of high-speed steel |
| - | Containing by weight not more than 0.7% of carbon, 0.5% or more but not more than 1.2% of manganese and 0.6% or more but not more than 2.3% of silicon; containing by weight 0.0008% or more of boron with any other element less than the minimum content referred to in note 1(f) to this chapter |
| - | Other |
| - | Other |
| - | Forged |
| 7224.B.B.B | Other |
| 7224.B.B.B.A | Hot-rolled or obtained by continuous casting |
| - | Containing by weight not less than 0.9% but not more than 1.15% of carbon, not less than 0.5% but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum |
| - | Other |
| - | Forged |
| 7224 | Other alloy steel in ingots or other primary forms; semi-finished products of other alloy steel |
| 7224.C | Ingots and other primary forms |
| - | Of tool steel |
| - | Other |
| 7224.D | Other |
| 7224.D.A | Of tool steel |
| - | Of rectangular (including square) cross-section |
| 7224.D.A.A | Other |
| - | Hot-rolled or obtained by continuous casting |
| - | Other |
| 7224.D.B | Other |
| 7224.D.B.A | Of rectangular (including square) cross-section |
| 7224.D.B.A.A | Hot-rolled or obtained by continuous casting |
| 7224.D.B.A.A.A | The width measuring less than twice the thickness |
| - | Of high-speed steel |
| - | Containing by weight not more than 0.7% of carbon, 0.5% or more but not more than 1.2% of manganese and 0.6% or more but not more than 2.3% of silicon; containing by weight 0.0008% or more of boron with any other element less than the minimum content referred to in note 1(f) to this chapter |
| - | Other |
| - | Other |
| - | Forged |
| 7224.D.B.B | Other |
| 7224.D.B.B.A | Hot-rolled or obtained by continuous casting |
| - | Containing by weight not less than 0.9% but not more than 1.15% of carbon, not less than 0.5% but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum |
| - | Other |
| - | Forged |
| 7225 | Flat-rolled products of other alloy steel, of a width of 600 mm or more |
| 7225.A | Of silicon-electrical steel |
| 7225.A.A | Grain-oriented |
| 7225.A.A.A | Of a thickness exceeding 0.16 mm |
| - | With a maximum core loss not higher than 0.9 w/kg |
| - | With a maximum core loss higher than 0.9 w/kg but not higher than 1.05 w/kg |
| - | With a maximum core loss higher than 1.05 w/kg |
| - | Other |
| 7225.A.B | Other |
| 7225.A.B.A | Hot-rolled |
| - | Products clad, plated or coated, not in coils, without patterns in relief, of a thickness exceeding 10 mm and products clad, plated or coated, not in coils, without patterns in relief, of a thickness of 4.75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more |
| - | Other |
| - | Cold-rolled |
| 7225.B | Other, not further worked than hot-rolled, in coils |
| - | Of tool steel |
| 7225.B.A | Of high-speed steel |
| - | Not further worked than rolled; not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square) |
| - | Other |
| - | Other |
| 7225.C | Other, not further worked than hot-rolled, not in coils |
| - | Of tool steel |
| - | Of high-speed steel |
| 7225.C.A | Other |
| - | Of a thickness exceeding 10 mm |
| 7225.C.A.A | Of a thickness of 4.75 mm or more but not exceeding 10 mm |
| - | Of a width of 2 050 mm or more |
| - | Other |
| - | Of a thickness of less than 4.75 mm |
| 7225.D | Other, not further worked than cold-rolled (cold-reduced) |
| 7225.D.A | Of high-speed steel |
| - | Not further worked than rolled; not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square) |
| - | Other |
| - | Other |
| 7225.E | Other |
| 7225.E.A | Electrolytically plated or coated with zinc |
| - | Not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square) |
| - | Other |
| 7225.E.B | Otherwise plated or coated with zinc |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7225.E.C | Other |
| 7225.E.C.A | Not further worked than surface-treated, including cladding or simply cut into shapes other than rectangular (including square) |
| - | Painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| - | Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7225.E.C.B | Other, of a thickness exceeding 10 mm or of a thickness of 4.75 mm or more but not exceeding 10 mm and of a width of 2 050 mm or more |
| - | Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7225.E.C.C | Other |
| - | Painted, varnished or coated with plastics on at least one side, excluding so-called "sandwich panels" of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| - | Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7226 | Flat-rolled products of other alloy steel, of a width of less than 600 mm |
| 7226.A | Of silicon-electrical steel |
| 7226.A.A | Grain-oriented |
| 7226.A.A.A | Of a width exceeding 500 mm |
| 7226.A.A.A.A | Of a thickness exceeding 0.16 mm |
| - | With a maximum core loss not higher than 0.9 w/kg |
| - | With a maximum core loss higher than 0.9 w/kg but not higher than 1.05 w/kg |
| - | With a maximum core loss higher than 1.05 w/kg |
| - | Other |
| 7226.A.A.B | Of a width not exceeding 500 mm |
| 7226.A.A.B.A | Of a thickness exceeding 0.16 mm |
| - | With a maximum core loss not higher than 0.9 w/kg |
| - | With a maximum core loss higher than 0.9 w/kg but not higher than 1.05 w/kg |
| - | With a maximum core loss higher than 1.05 w/kg |
| - | Other |
| 7226.A.B | Other |
| 7226.A.B.A | Not further worked than hot-rolled |
| - | Products clad, plated or coated |
| 7226.A.B.A.A | Other |
| - | Of a width not exceeding 350 mm and of a thickness of 50 mm or more |
| - | Other |
| 7226.A.B.B | Other |
| - | Of a width exceeding 500 mm |
| - | Of a width not exceeding 500 mm |
| - | Of high-speed steel |
| 7226.B | Other |
| 7226.B.A | Not further worked than hot-rolled |
| - | Of tool steel |
| 7226.B.A.A | Other |
| 7226.B.A.A.A | Of a thickness of 4.75 mm or more |
| - | Of a width not exceeding 350 mm and of a thickness of 50 mm or more |
| - | Other |
| - | Of a thickness of less than 4.75 mm |
| 7226.B.B | Not further worked than cold-rolled (cold-reduced) |
| - | Of a width exceeding 500 mm |
| - | Of a width not exceeding 500 mm |
| 7226.B.C | Other |
| - | Electrolytically plated or coated with zinc |
| 7226.B.C.A | Otherwise plated or coated with zinc |
| - | Aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Plated or coated by hot dip galvanisation, whether or not alloyed with silicon; chemically passivated; with or without any additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7226.B.C.B | Other |
| 7226.B.C.B.A | Of a width not exceeding 500 mm, hot-rolled, not further worked than clad; of a width exceeding 500 mm, not further worked than surface-treated, including cladding |
| - | Painted, varnished or coated with plastics on at least one side, excluding products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| - | Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with or without additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7226.B.C.B.B | Other |
| - | Painted, varnished or coated with plastics on at least one side, excluding so-called "sandwich panels" of a kind used for building applications and consisting of two outer metal sheets with a stabilising core of insulation material sandwiched between them, excluding those products with a final coating of zinc-dust (a zinc-rich paint, containing by weight 70% or more of zinc) and excluding products with a substrate with a metallic coating of chromium or tin |
| - | Plated or coated by hot dip galvanisation with magnesium and/or aluminium, whether or not alloyed with zinc, whether or not alloyed with silicon; chemically passivated; with or without additional surface treatment such as oiling or sealing; containing by weight: not more than 0.5% of carbon, not more than 1.1% of aluminium, not more than 0.12% of niobium, not more than 0.17% of titanium and not more than 0.15% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other, aluminium killed; plated or coated by hot dip galvanisation with zinc and/or with aluminium, and no other metal; chemically passivated; containing by weight: 0.015% or more but not more than 0.170% of carbon, 0.015% or more but not more than 0.100% of aluminium, not more than 0.045% of niobium, not more than 0.010% of titanium and not more than 0.010% of vanadium; presented in coils, cut-to-length sheets and narrow strips |
| - | Other |
| 7227 | Bars and rods, hot-rolled, in irregularly wound coils, of other alloy steel |
| - | Of high-speed steel |
| - | Of silico-manganese steel |
| 7227.A | Other |
| - | Containing by weight 0.0008% or more of boron with any other element less than the minimum content referred to in note 1(f) to this chapter |
| - | Containing by weight 0.9% or more but not more than 1.15% of carbon, 0.5% or more but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum |
| - | Other |
| 7228 | Other bars and rods of other alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or non-alloy steel |
| 7228.A | Bars and rods, of high-speed steel |
| - | Not further worked than hot-rolled, hot-drawn or extruded; hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Forged |
| - | Other |
| 7228.B | Bars and rods, of silico-manganese steel |
| 7228.B.A | Of rectangular (other than square) cross-section, hot-rolled on four faces |
| - | Not further worked than hot-rolled, hot-drawn or extruded |
| 7228.B.A.A | Other |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7228.B.B | Other |
| - | Not further worked than hot-rolled, hot-drawn or extruded; hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7228.C | Other bars and rods, not further worked than hot-rolled, hot-drawn or extruded |
| - | Of tool steel |
| 7228.C.A | Containing by weight 0.9% or more but not more than 1.15% of carbon, 0.5% or more but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum |
| - | Of circular cross-section of a diameter of 80 mm or more |
| - | Other |
| 7228.C.B | Other |
| 7228.C.B.A | Of circular cross-section, of a diameter of |
| - | 80 mm or more |
| - | Less than 80 mm |
| - | Of rectangular (other than square) cross-section, hot-rolled on four faces |
| - | Other |
| 7228.D | Other bars and rods, not further worked than forged |
| - | Of tool steel |
| - | Other |
| 7228.E | Other bars and rods, not further worked than cold-formed or cold-finished |
| - | Of tool steel |
| - | Containing by weight 0.9% or more but not more than 1.15% of carbon, 0.5% or more but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum |
| 7228.E.A | Other |
| 7228.E.A.A | Of circular cross-section, of a diameter of |
| - | 80 mm or more |
| - | Less than 80 mm |
| - | Other |
| 7228.F | Other bars and rods |
| 7228.F.A | Of tool steel |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7228.F.B | Other |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| 7228.G | Angles, shapes and sections |
| - | Not further worked than hot-rolled, hot-drawn or extruded |
| 7228.G.A | Other |
| - | Hot-rolled, hot-drawn or extruded, not further worked than clad |
| - | Other |
| - | Hollow drill bars and rods |
| 7229 | Wire of other alloy steel |
| - | Of silico-manganese steel |
| 7229.A | Other |
| - | Of high-speed steel |
| - | Containing by weight 0.9% or more but not more than 1.15% of carbon, 0.5% or more but not more than 2% of chromium and, if present, not more than 0.5% of molybdenum |
| - | Other |
Need help to the find appropriate HS Code ?
or